Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> rocker panels ????
User Name
lost password?   |   register now

Thread: rocker panels ???? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-16-2009 08:31 PM
68FB347 ok ....... much thanks
11-16-2009 02:02 PM
deadbodyman Yes,but not for the floor,just before you cut the rockers.they'll just be in the way..
11-16-2009 09:11 AM
68FB347 thanks .... that helps give me an idea how to get started .... do I need to weld braces across the door opening or body?
11-15-2009 04:53 PM
deadbodyman I'd start with the floor,start where the floor meets the rocker and cut along that edge..cut a section of the floor thats a lot smaller than the new floor but big enough to set the new floor in and mark all the way around the edge of the of the old floor to show you where it needs to be cut then cut it two inches below the line all the way around...use drill screws to fasten the new floor down tightly and re mark it again for a closer cut with a 1/2 of lea-way all the way around weld one side then underneath then move to the rocker dont forget to punch holes in the floor where it folds down to meet the rocker you'll need them for welding the floor to the rocker.
11-15-2009 01:33 PM
68FB347 i'm using dynacorn one piece floor pan and repro rocker panels
11-15-2009 07:24 AM
302 Z28 Cut the old one off, weld the new one on. . Seriously that is like asking how to do a nice paint job in one paragraph. I suggest you lurk here for a while and read every thing you can about body work. Also you might purchase some good body shop books I'm sure will be suggested further down in this thread. There are some very good resources in this forum that can offer some valuable tips and photos. The work involved can run the gamut from fairly sophisticated to a real bugger.

11-15-2009 07:23 AM
deadbodyman Since the rockers are part of the integrity of the car reinforce the door jambs first and only do one at a time its not much differnt than replacing a 1/4 panel you'll need some tools,air chisel ,sawzall,hole punch ,drill screws,etc...are you using used rockers and pans or new? after market or ford?
11-15-2009 06:46 AM
rocker panels ????

can someone give a brief "how to " on replacing rocker panels on a 68 Mustang FB. I will replace both inner and outer rocker panels . I am also replacing floor pans .

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 01:54 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.