Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Has anyone used a 3M Bristle Disk
User Name
Password
lost password?   |   register now

Thread: Has anyone used a 3M Bristle Disk Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-14-2009 12:47 PM
Hot Rod Mike
3M bristle discs/Roloc discs

While I have used these to strip paint in some areas of a vehicle, I think there are other means to do so @ a lower cost. However, I have used these in the past to clean up an area where I might be welding, to eliminate any rust or minor corrosion or other surface abnormalities. They are helpful also to get the temps of the sheet metal up so that the 1st welds are not on "cold metal". Even thought my garage is heated, the metal in the winter time is cold to the touch, so I just run these around a little on the area to be welded to warm up the metal.

Regards,
Mike.
12-12-2009 07:35 PM
chadngarrett Thanks for the advise .. you guys gave been great
12-12-2009 10:53 AM
radir68 Yeah those roloc gasket discs are killer for jambs and you are right about using them up. Check out www.smartshoppersinc.com they have a house brand that helps keep the cost dowm. Have fun
12-12-2009 06:32 AM
deadbodyman I've used a lot of things to strip paint including those,but the best I've found so far for stripping jambs and such are the rol-loc brown cookies (gasket cleaners) they dont leave any grinding marks and are pretty cost effective plus as they wear you can use smaller and smaller backing plates till theres nothing left...the smaller they get the tighter the spot you can use them in.Those green things just wear to fast for me...
12-10-2009 10:41 AM
radir68 Eastwood has a disc set up for the 41/2 and 8 inch grinders. They are designed for stripping paint and work very good. The down side is you have to buy the backing plates for the grinders. Have fun
12-09-2009 07:08 AM
chadngarrett Thanks for the advise...
12-08-2009 09:10 AM
S10xGN
Quote:
Originally Posted by chadngarrett
i was thinking rather then have the body soda blasted we could get 2 of those and go to town working on the large surface areas .
Although I've never used that type, I think you'll find yourself buying way more than 2. They will wear out pretty quick...

Russ
12-08-2009 09:00 AM
chadngarrett so use the bristle for the big areas and use



for the seams and edges
12-07-2009 02:39 PM
stimpy we used those to finish spots the blaster missed ,they work great , prepare to use alot of them if your going to try to strip a large area they kind of wear out quickly ,
12-07-2009 02:15 PM
OneMoreTime That is what a lot of us do...an airmotor with a 2' roloc will work on some of the tighter areas and a small HF spot blaster for the seams and such and you are good to go..just do what you can and at the end of the day shoot some epoxy primer on the cleaned areas and move on..


Sam
12-07-2009 12:29 PM
chadngarrett i was thinking rather then have the body soda blasted we could get 2 of those and go to town working on the large surface areas .
12-07-2009 12:06 PM
OneMoreTime Those things are useful in some circumstance..I used those to prepare a truck bed for bed-liner..

Sam
12-07-2009 11:57 AM
chadngarrett
Has anyone used a 3M Bristle Disk

Has anyone used a 3M Bristle Disk to remove paint and or rust ?



I think I want to buy a couple right angle grinders and get to work on G-mans cab.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:07 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.