|01-02-2010 07:08 PM|
|krazeyone||ok, i'm no profesional, but i have a 50 chevy fleetline with alot of curves. i baught those durablocks, and love them. there are only so many durablocks vs. so many different curves on a car, so sometimes i had to look around the garage and find what i could use to do those funky curves. whenever i had an outside curve that was a pain i used one of those black 3-m rubber squeeges, the bigger 3 x 4 inch ones you would use when wetsanding. i would put my sticky back paper on it. you can run it under hot water to make it more supple an it will conform to your surface. put the paper on it after you give it a bend in the way you want it to stay, so when your sanding it won't get any kinks in the paper and use the x and straight across patern. worked like a charm for me.|
|12-31-2009 01:38 AM|
|deadbodyman||I got a bunch of differnt size pvc pipes I use all the time but they dont flex.so I 've been using heater hose and radiator hose with sticky paper on them but they arnt stiff enough for a lot of jobs.I've got at least two hundred bucks worth of dura blocks but this will be real handy for the unusual shapes you run into I can even put steel wire in the block so I can bend them and keep a contour.....Man ,I've used a crap load of that foam and never even thought of that....Thanks that'll keep me busy for a couple days...|
|12-30-2009 11:13 PM|
"OBM,will sticky back paper stick to that spray foam without tearing the foam up when you replace the paper?"
All sticky back papers are not the same, 6" DA usually works fine, long board usually has a death-grip. You can test your's on the back side first, if it's too sticky run it over your pant leg once or twice to kill the stick. Don't leave the paper on over night, it won't come off without heat.
Have fun with it, it can be a real time saver.
|12-30-2009 10:28 PM|
A tip would be to not change sand stoke direction in the same place twice ..
guide coat is indeed your friend
|12-30-2009 10:28 PM|
|deadbodyman||OBM,will sticky back paper stick to that spray foam without tearing the foam up when you replace the paper? I figure I can make forms out of wood or PVC and make some handy blocks with that stuff.|
|12-30-2009 10:03 PM|
"My God, that sounds harder than building the thing!"
not really, it takes longer to type it than do it. I stole that one from the guys at the boat shop but they do it reversed.
They took disc adhesive and glued a full sheet to the haul then cut a piece of hard Styrofoam foundation insulation and sanded that against the haul to make a sanding block, PERFECTLY sized with the paper. A real time saver on large areas. It will show when it's out of it's area by hitting in center or on the edges.
A bodyshop would only use this for odd shapes, multi-bevel door jam, roof ribs, style-lines on a pick-up bed, multi-grooved doors, VW fenders Anything that saves time is worth a look.
|12-30-2009 09:19 PM|
|deadbodyman||That wad of of wet paper is a great way to sand any curve.the water keeps the paper sucked right up to the work if you take your hand off and walk away the paper will still be stuck there when you get back.Old Willie showed me a lot of handy little tricks (RIP) Mean old coot ,but knew his stuff.I'll tell ya what though sanding a curved car is easier than a straight slab of steel...|
|12-30-2009 09:00 PM|
|deadbodyman||Hymmm ,spray styrofoam.....now you got my brain working I see lots of possibilities here ....WC everything sounds normal with your primer try wet sanding it'll be faster and easier. 320 - 400 oughta do it the water keeps the paper clean....|
|12-30-2009 08:52 PM|
My God, that sounds harder than building the thing!
I found some interesting sanding pads at Ace. Three in a pack and they can be stacked kind of like your wet sandpaper concept in order to give them a little stiffness.
I think (hope) they might do the trick, working in small areas at a time w/some guidecoat.
It's just one of those scary things because you aren't really gonna know til you get the paint on it and it's too late...
|12-30-2009 08:44 PM|
IF all else fails, an old pirate's trick:
(you will need 6" stick-it DA paper, Saran Wrap, spray-can Styrofoam home insulation)
1. cut 8 1.5" pie shaped slices around the paper, should leave a 3" sun and 8 rays, save the clippings
2. place paper over a coffee cup of hot water, the stream will let the paper go limp
3. place paper, grit up, where you wish to work, start at center and layout flat, install clippings into slots. Make it pretty, style points count
4. cover area with Saran-Wrap, no wrinkles.
5. apply Styrofoam to cover paper size and allow to cure
6. trim sanding block to fit your hand but slightly larger than the paper
7. install new paper grit down and attach sanding block, check for perfect contact, the slots leave somewhere for the dust to flow.
8. go to town with your brand new, PERFECTLY sized and shaped sanding block. These only work for a small area thanks to constantly changing curves, you will see and fell the limit instantly.
Guide coat is your friend, patience is a virtue and Happy New Year.
|12-30-2009 10:00 AM|
I'm looking forward to trying all the techniques suggest. I'm praying I don't have to resort to your wet sanding idea, though. I think there would be ice floating in my bucket this morning...
|12-30-2009 06:44 AM|
|deadbodyman||It sounds like its hardened to me.I dont know why it would roll and clog the paper,unless you used the wrong reducer or hardner by mistake. I've done that too,I had to check all the levels of all my hardners. What grit paper are you sanding with? wet or dry?do you have any other paint materials on the same bench as the primer? One more thing... 180 and finer grits get packed with powder pretty quick, You have to slap the pad with a paint paddle or something to loosen it up and clean the paper when you dry sand , wet sanding works better. in my opinion. also if you lay down your guide coat to thick it;ll roll too but its the guide coat rolling not the primer.If it sounds like I've made a lot of mistakes in my life as a body & paint man, your right I have, No need for you to too.try a few of these ideas and let us know.I cant have made every screw up..but these are some of the ones I remember.|
|12-29-2009 11:58 PM|
I honestly don't know why there would be a problem. I'm sure I catalyzed it. In fact, my problem seemed to be the opposite. I had to strip it all off the box because of dry spray.
|12-29-2009 09:14 AM|
|deadbodyman||Nason 2k is the primer I was talking about. I forgot to catalyze a 2k primer twice when feather fill first came out I was used to lacquer primer (industry standard) at the time.so i know your pain. I wouldn't think its the problem if its not soft. BUT.. I am the local expert around here at removing un catalyzed primers and paints (the last time I mixed clear and wasnt paying attention I mixed a 1:1 clear at 4;1) and pretty much fixing any kind of screw up...every time I think I've screwed everything up there is and cant possibly screw anything else up ,I amaze myself....seriously though If you need to get it off I can help make it easier,lets hope thats not the case.Can you gouge the primer out with your finger nail?|
|12-29-2009 07:51 AM|
|This thread has more than 15 replies. Click here to review the whole thread.|