|09-17-2014 04:13 PM|
|aisr||I use them to minimize the amount of oil that gets thrown onto my cylinder walls, just one of the things that helps me run my street/strip car with minimum ring tension. The last version had 12lb oil rings and ran down the freeway at 3000rpm, only added 2 qts of oil all summer (about 3500mi). This winter it's getting even lighter rings.|
|09-16-2014 07:15 PM|
Buy the best oil pan you can afford, to control windage from the bottom up....rotating crank assembly pulling oil out of the pan upwards is more of an issue than what little is coming back down from the top end.
Spend your money on the bottom, on a pan with catch pockets, scrapers, gates and tray..
|09-15-2014 08:14 PM|
|Biscayne327||hey its fun and windage is windage.|
|09-15-2014 08:09 PM|
|09-15-2014 09:18 AM|
"I bet my station wagon can beat your corvette, 200 laps on the road course, lets go!"
It is way overkill for the street, but for some people it's just something else to do on their car, the fun is in the tinkering.
|09-15-2014 08:51 AM|
|09-15-2014 08:13 AM|
|ap72||You could install a cam tunnel instead of stand offs. It can be made to redirect oil around the crank, but has the added benefit of keeping your cam and lifter submerged in oil.|
|09-15-2014 07:42 AM|
|Richiehd||Im a middle of the road guy! I use four standoffs on one side only, the passenger (right) side to prevent oil from blowing back up into the valley and help with windage. (just my 2 cents)|
|09-15-2014 06:14 AM|
|F-BIRD'88||Funny how none of the OEM factory race efforts neither used or promoted any of this eye wash.|
|09-14-2014 09:49 PM|
|Biscayne327||I had plugs in my 327 block and the cam after 12 years was fine , I should think that there is enuff splash from the crank so you really don't need those holes.|
|01-10-2010 12:17 PM|
I'd just love to see 6 dyno pulls in a row with the motor running at max hp for say 5 minutes on a mule motor without these then 6 more pulls with them all other conditions being the same. This would give a good average and take into account the dyno tolerances and allow the oil to flow. I'd bet there wouldn't be much if any difference.
I wish I'd thought of the items. Could probably finance another project. haha
|01-10-2010 11:42 AM|
|sexypizzaman||well put bogie, I will forget it then, besides, wouldn't you rather be on the safe side having more getting to the cam than not enough?|
|01-06-2010 10:22 AM|
While I think that if you just gotta try out your tap and die set, the stand offs are a better solution than plugs, as they at least provide a path for blow by that isn't sharing the same holes as oil drain-back on the ends of the block. But in the bigger picture I have to wonder if all this gnashing of teeth over those quarter inch holes is worth it to anyone but the purveyors of tap and dies sets, stand off vents, or hole plugs.
|01-05-2010 10:55 PM|
|4 Jaw Chuck||Meh, save your money. Not a mod you need to make for any street car and a questionable one for an all out race car at that.|
|01-05-2010 07:33 PM|
|DoubleVision||Unless your on a race track trying to win money and trying to squeeze every last horsepower out of the engine as possible I`d say these are a good idea. If it`s just a street machine I`d say don`t waste your time.|
|This thread has more than 15 replies. Click here to review the whole thread.|