|02-15-2010 12:39 PM|
My Singer 111W153 cost me a total of 400 bucks. Everything was used.
|02-02-2010 10:21 AM|
|DanTwoLakes||I replaced the clutch motors on all three of my machines. Much easier never to have to worry about the machine so I can just concentrate on what I'm sewing.|
|02-02-2010 09:32 AM|
|ronbo||Did get the servo motor. As you may remember, starting and stopping gives us noobies trouble, same as learning to drive!!|
|02-02-2010 07:11 AM|
Your machine is a lot like the Consew 205 and 206 which has the bobbin on the left of the needle. If you ever try a servo motor, you will never go back to a clutch motor.
|02-02-2010 06:42 AM|
AS one of the subscribers mentioned, many machines are copies of various Singers. Just by the model number of yours, I would say that was the case.
I have heard that Tacksew was a nice machine. In 40 years, I have never worked with a servi motor. We had machines that would do auto back tack, thread trimming, needle positioning, etc, but no servo motors.
I have 2 Pfaff 545's, a Pfaff 1245 and a Pfaff 138 in my garage right now, but haven't done much sewing for some time.
|02-01-2010 07:01 PM|
I recently purchased a Tacsew 111-155W. My plans are to sew my interior and perhaps a couple more. Mostly figuring and practicing so far!
|02-01-2010 03:42 PM|
I bought the Tacsew T111-155 pictured below to do my first interior. I selected this machine based on a number of recommendations by members here on HR.Com.
It is a walking foot, compound feed machine with 1/2" clearance under the presser foot. I also got the optional 3/4 hp servo motor. The total cost, with server, shipped to my door was just a hair under $950 and I got it from SewingGold.com
As a totally rookie the servo motor was really a life saver. But even with a servo, I still fabricated an adjustable stop (shown in second photo below) to limit the maximum speed I could run the machine. It takes some practice to get used to the touch of the servo and I would occasionally give it way too much gas and things would sort of get away from me. So the adjustable stop has been really helpful.
I've had a great time sewing with this machine and it handled everything I threw at it with ease. Any and all flubs on my interior were totally due to the operator...not the machine.
|02-01-2010 11:11 AM|
|DanTwoLakes||Yes, the Pfaff parts are more expensive, but not ridiculously expensive. A welt foot for a Consew, Singer, or Juki is $18.95, and the same thing for Pfaff is $29.95. The Pfaff machines are great machines, and that is what I learned on. All of these machines are basically copies of the original Singer 111W, which has been the workhorse of the industrial sewing machine world for a long, long time. Any of them will work well for you, especially if you are only using the machine for your own use, and not making a living with it.|
|02-01-2010 09:05 AM|
As you can see, sewing machine preference is about the same as do you drive a ford or Chevy. If you work in a shop that uses Juki, you may be more comfortable using a Juki.
I worked for 40 years and my choice was always Pfaff. Everyone says parts are expensive, but many are available as generic parts, including presser feet. I started on a Pfaff 145, but as soon as the 545 came out with a 50% larger bobbin, that was a no brainer. The initial 1245 had automatic oiling for the bobbin. They eventually moved away from that.
With the Pfaff's there are H3's and H4's. The H3 doesn't lift as high as an H4 and they take different needles. I prefer the H4. The newest 1245 has reverted back to the H3 lift height.
The key is it makes life easier if the machine is a walking foot, whether it is a Pfaff, Juki, Consew or Singer.
Hope the helps.
|01-27-2010 07:48 PM|
been using an older consew 206rb-1.
clutch motor, servo would be nice, but i've gotten used to the clutch.
bobbins are a pain but got used to that as well in the last 20 or so years.
old girl is starting to show her age though.
may have to upgrade to something newer in the next couple years.
|01-25-2010 01:29 AM|
|01-24-2010 11:05 AM|
|DanTwoLakes||If it's a Rex 11-155R or a Nakajima DBU-180L, it is like a Consew 205RB, which would make it a compound feed walking foot machine. That would work fine for auto upholstery.|
|01-24-2010 07:48 AM|
Rex - Nakajima sewing machine
Anyone familiar with a Rex - Nakajima sewing machine with walking foot? I found one on cr-list. Is this something I can use for auto interiors?
|01-15-2010 11:34 AM|
|01-15-2010 10:57 AM|
Yea, I kinda have to agree with ya on your points - I had attempted my first seat cover (90-ish Cavalier bucket) last weekend and the limited space on the right really made things interesting. I will say that I was able to cram 3 layers of 1/2" sewfoam/gripstitch and vinyl assemblies under the foot, but ya had to watch and make sure it fed correctly and didn't get hung up. I will say that the smaller HP motor was perfectly adequate for what I've done so far. There's 2 sets of belts/pullies so it's geared down quite a bit for the increased torque - don't know how the speed compares to a real industrial machine except that it's plenty fast for my skill level.
As for feet, its got the standard, left-zipper, right-zipper, and leather foot - mainly the basics. The leather foot doesn't have the sharp teeth that the standard one does, and both the leather & standard have channels for piping.
It works good for shifter boots, though
|This thread has more than 15 replies. Click here to review the whole thread.|