Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> 1st attempt at fiber glass
User Name
lost password?   |   register now

Thread: 1st attempt at fiber glass Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-31-2010 12:18 PM
68Birdman2 Thanks for the input Dan. I got the reply a little late and stretched the vinyl around it. Had to heat it a little with the heat gun but it came out ok. Couple little spots that I don't like.

01-31-2010 10:38 AM
DanTwoLakes You need to cut it and sew it to fit. Take a look at this thread and you'll see what I mean. CLICK HERE
01-31-2010 08:28 AM
68Birdman2 Dan
Do you think it will be dificult to strecth the vinyl over it? Considering the shape.
01-31-2010 08:23 AM
DanTwoLakes If it's smooth enough, you don't need the closed cell foam under it. If not, you will see every imperfection telegraphed through the vinyl.
01-31-2010 08:18 AM
68Birdman2 [IMG]You should'nt have a problem covering it with fiber glass. Definately go the the fiberglass forum because there is a lot of good info on that forum.

Here's what I did with console. Have to decide wether to paint it or cover it in vinyl. Do you guys thing I ought to cover the sides with 1/8" CSF and then vinyl or don't use any foam at all. I plan on putting wood on the bottom where the radio goes and also the top where the vintage air ac control and vent go.[/IMG][IMG][/IMG]

01-30-2010 08:30 PM
fiberglass forum

In my opinion this forum, hot rodders .com, has more practical and useable info than the one you mentioned above.
01-30-2010 02:33 PM
01-30-2010 11:01 AM
"form" left in?

I'm going to try (key word=try) doing a console with glass. It's wood now, 3/4" finger joint covered in vinyl.

If I remove the vinyl can I glass the outside of it and just leave the wood in it for good?
01-25-2010 07:01 PM
Glass is fun

It's fun what you can do with fleece & resin. I made a molded speaker box this way several years ago. Here is how I did it: I made my speaker rings from 3/4" MDF and made stands from some scraps to hold them in place. I stretched my fleece tight and stapled it to the rings and being sure to pull out all the wrinkles. Pulling the fleece back to the sides of the box and staple back to the sides. Before you pour on the resin make sure that the shape is something you will be happy with. Be liberal with the resin (I used just a standard fiberglass resin and liquid hardener, mix per the directions) You must work quickly on this part as the resin will start to congeal in 10 min depending on the temperature. After you have coated all the cloth and completely saturated. Let dry completely until it is hard. Then take a DA with 80 grit and knock off the fuzz of the fleece. Remove the stands and finish with a good quality plastic filler, then putty finish with 220 grit. Throw on a primer. Then if you are planning on vinyl you're ready to go, just a little spray adhesive and vinyl. Remember how you pulled the wrinkle out of the fleece as you will have to do the same with the vinyl. Leave it out in the sun or under a heat lamp. I'm know I short cut some of this. Let me know if you want some details of any of the steps.
01-25-2010 06:56 AM
1st attempt at fiber glass

This is my first attempt at a console. I mocked it up with wood and superglue and then pulled it out and fiberglassed the inside of the wood and cloth with 3 layers of fiberglass. Then put it back in and fiberglassed the edge to try and get the contour of the dash. I didn't reinforce the gauge pod. Next I plan on pulling it out and duraglassing the console. My plan is to cover the console with vinyl. Some questions
1. Can I duraglass the edges at this point?
2. Can I reinforce the back of the pods or do I have to glass the outside?

Any thought from the would be appreciated.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 12:19 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.