Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Assistance with my 383 >
User Name
Password
lost password?   |   register now

Thread: Assistance with my 383 > Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-04-2010 09:52 AM
454C10 here is a nice intake comparison.

http://books.google.com/books?id=Y98...age&q=&f=false

it is on a bbc. the performer and torker make the same peak hp and torque. But the performer made max torque 600 rpms sooner. That is what I felt in my sbc power z car when I tried the torker.
02-04-2010 09:22 AM
cobalt327
Quote:
Originally Posted by ERASER
just going to drive my car to work daily, all highway for about 15 mins. one way. I have two Intakes , an Edel Preformer & an Edel Torker 2 & a Holley 700 DP. I know I need a bigger cam & plan on going up to a 285. What intake should I go with ?
If you have to use either/or, I'd stick w/the Performer- knowing that it'll cost some top end (maybe) compared to the Torquer II.

What you should consider is an RPM or knock-off. Air Gap if you must, but I like just the RPM- although this is solely based on here-say.

You can fart around w/spacers on either one and gain (or lose) power. I'd suggest making your own, buy them at a swap meet or be prepared to shell out some coin. Open spacers can be found cheap, but the double throw-down swirly-twirly ones are $$$.
02-04-2010 08:46 AM
ap72 I'd run the torker intake with a 1" open carb spacer.
02-04-2010 08:18 AM
79z
assistance with my 383

with my 454 z28 i ran the same 1/4 mi. times w/ enither intake. t6hrottle response was similar. although i had the old schoole torker w/ thetwisted carb location.
02-04-2010 07:30 AM
454C10 If you really want to make more power then get some good aftermarket heads. in most cases, ported stock heads are nearly as good.

what gears, what stall, what compression? all these things need to match along with the cam used.

a 270H is a good all around cam. With a large engine like the 388, it should run well with a wide range of parts. 3.08 to 3.55 gear, 2000 to 2400 stall, 9 to 9.5:1 cr.

I would run the performer intake over the torker. You may need to use a carb adaptor on the performer intake as most of those intakes use a spread bore pattern. How much hood clearance do you have? I would prefer the performer RPM intake with a square bore pattern for the holley.

don't expect good mpg with a 700DP. A 3310 750 vac secondary carb would be better for mpg.
02-04-2010 06:43 AM
ap72 put your money towards a GOOD set of headers.
02-04-2010 06:01 AM
ERASER Thanx guys ! I appreciate it tremendously !
02-03-2010 09:28 PM
Double_v23 Torker 2 is an awful intake, stick with the performer, unless you have a lot of compression and some decent gears I wouldn't change the cam either.
02-03-2010 08:29 PM
killerformula with the current cam it wouldn't make sense to run anything that will run over 6000 RPM, maybe less. Use the performer for now. If you do upgrade the cam later consider something with higher RPM potential (although I'd still strongly recommend a dual plane).

K
02-03-2010 06:55 PM
ERASER
Assistance with my 383 >

Hey fellas, I'm pretty green to Engine Building. I have a Freshly rebuilt 383 stroker.

2 bolt main

Bored .30 over

Comp cams magnum 270h hydraulic flat tappet cam & lifter kit

Comp cams push rods

Comp cams magnum double roller timing chain

High flow oil pump

Freshly rebuilt port & polished 202 heads

Now, I am probably just going to drive my car to work daily, all highway for about 15 mins. one way. I have two Intakes , an Edel Preformer & an Edel Torker 2 & a Holley 700 DP. I know I need a bigger cam & plan on going up to a 285. What intake should I go with ?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.