Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> how much is to much
User Name
lost password?   |   register now

Thread: how much is to much Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-24-2002 02:29 PM
4 Jaw Chuck The small block Chev is an easy one to figure out how much to remove from the intake manifold face to match your shaved heads. Since the heads intersect the block at 90 degrees and the intake face is also at 90 degrees you would remove exactly half the amount off of each intake face.

For example, if you shave the heads or block 0.010" you would have to remove exactly 0.005" from each intake manifold face to retain the original orientation. This only applies to engines that have 90 degree gasket surfaces.

To do engines with less or more than 90 degree gasket faces use this simple formula,
For a 60 degree V6 with 0.010" shaved from the head: TAN 60 X (0.010" / 4) = 0.0043" from each intake manifold face.

Just remember to check the manifold faces to be sure you have the correct angle, not all engines have 90 degree gasket faces.

Hope this helps.

[ April 24, 2002: Message edited by: 4 Jaw Chuck ]</p>
04-23-2002 07:58 PM
wrenchturner Thanks for the response, small block chev. I'm gonna catch some flack, experimenting with 305 heads. I've done them up. They look good. They look like they may breath, for what they are. I used a block that was cracked down towards the lifters. A good friend of mine operates a machine shop, told me I would be alright because the crack was towards the lifters. Water in oil. Don't know for sure where water's coming from. Suspect the block. Never had any problem with the van it came out of. Took my 383 block, redone, used it, gonna try again. Trying to figure out where water's coming from. Thanks again. When it rains, it pours!
04-23-2002 12:49 PM
johnnymopar wrenchturner,

i don't know what kind of engine you have, but i have some smallblock mopar engine-building books. For those it suggests the max. amount you would plane off the head would be 0.060" and for every 0.010" taken off the head, the intake should have 0.0095" removed. Probably not the same for all engines but maybe you can use this as a guide.

04-23-2002 05:15 AM
how much is to much

can anybody tell me when milling heads how much does it take before you start having intake misalignment problems and ect.appreciate any input on this <img src="confused.gif" border="0">

[ April 23, 2002: Message edited by: wrenchturner ]</p>

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:08 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.