Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> 1963 galaxie trim removal
User Name
lost password?   |   register now

Thread: 1963 galaxie trim removal Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-17-2013 12:11 PM

If I remember right the trim piece was screwed in place then the weather strip installed. I don't know if they used adhesive also.
09-17-2013 10:50 AM
Bill Peasley
63 Galaxie top rail chrome

Originally Posted by bcovey View Post
Can any one tell me the best way to remove exterior trim from 1963 galaxie.
can anyone tell me how to remove the outside chrome on the top rail of a 63 fastback. do I need to do this to replace top rail weather strip? If not, what the heck do I need to do, help.
02-23-2010 01:38 PM

I sold mine in 66, but I think it is like later models with an H shaped weatherstrip , the molding was held in with clips over weld studs.... to prevent damage to paint you can apply a strip of masking tape. then use a putty knife, about1 inch wide works for me . start on the body metal side and pry a little to see where the clip is located and pry up gently, Usually start at the end of the overlap piece.. the first clip is usually a couple of inches from the joint. sometimes you have to work 2 spots at a time. If you have a pick your own part wrecking yard go and practice . some of the clips are different collors. have different shapes for different size moldings. If you break the weld studs the factory repair was to use a small drill point screw near the location. Screws used for metal wall studs work pretty good, pan head style.
02-23-2010 10:44 AM
1963 galaxie trim removal

Thanks for the information, How about the trim around the rear glass? This is a 631/2 fast back.
02-23-2010 07:10 AM

I 'm not sure if they used weld studs or push in metal grasshopper clips. Most moldings use a threaded stud at the ends Best to remove the interior panels as necessary . If you have the metal push in clips you need to squeeze the legs in, a small socket on a 1/4 hand driver sometinmes works or weld a piece of tubing to the end of an old screwdriver at 90 degrees to compress the legs to the same size as the drilled holes. then push out the legs with a piece of rod thru the tube. . For weld stud clips when you get the end nuts off gently pull the molding away from the body and a slight twist. use a plastic bondo spreader to work under the bottom edge to lift the molding. Most Ford moldings were designed with more curl (grip) under the top edge. Moldings that use metal clips have a wide spot under neath where the clip was inserted then slid to the mark on the assembley fixture to align with the holes. Most slide better one way than the other. ( 15 years as a Ford Engineer. a few in trim and elect).
02-22-2010 04:33 PM
1963 galaxie trim removal

Can any one tell me the best way to remove exterior trim from 1963 galaxie.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:45 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.