Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Newbie needs input.....
User Name
Password
lost password?   |   register now

Thread: Newbie needs input..... Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-25-2002 11:16 AM
Biggarmike 429 or 460 will also work, and as a secondary benefit is 75 -100 lb lighter. I'm not sure about all of the acessory brackets, motormounts, exhaust, etc. The FE is a direct bolt in.
The 4bbl manifold will help a little, but the bigger difference in the 2 bbl and 4 bbl FE engines was the compression ratio and cam. If you are using stock exhaust manifolds, the flat sided ones, big bore exhaust won't help. You will need either headers or the old style cast headers, they were a part of the performance options on various models through the 60's. There is a book floating around, I haven't seen one in a while but they must be available in reprint. "Holman-Moody Ford Factory Performance Parts Book" or something like that. It lists all of the casting numbers for the Ford engines of the 60's even the hard to find special order stuff. It is an invaluable aid for FE junkies at swapmeets and junkyards.
04-25-2002 09:50 AM
mustang66maniac Yeah that would be possible, edelbrock has some nice intakes for FE motors. Im pretty sure you could also fit a 429 or 460 in there too, they use the same tranny and there's more parts available for them becuase they were used until the mid 90's.
04-25-2002 07:13 AM
BIGNICK thanx for the quick reply....
I was also thinking of dumping a 4 bbl carb, with new intake, and then do 3 1/2" straight pipe..
is that possible at all?

thanx,

nick
04-25-2002 07:02 AM
Biggarmike An FE block will fit, they were available in that rascal as an option. FE block Fords (352,390,406,428) can make herds of HP, but parts arent cheap. A pre 66, 4 bbl motor from a full size car will likely be your best match. I think they were rated around 335 HP. If you are lucky one can be found in a junkyard, or in a long forgotten car, behind the neighbor's barn, etc.
04-25-2002 06:08 AM
BIGNICK
Newbie needs input.....

I have a 68 cougar, I am just wondering what is the biggest engine I am able to drop into it without doing anything to the frame. Any help or suggestions would be appreciated.

thanx,

nick

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:16 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.