Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> GM steering column won't lock!!
User Name
Password
lost password?   |   register now

Thread: GM steering column won't lock!! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-10-2010 05:26 PM
APalusky Will it make that much of a difference that I cut it off?? I could leave it where I have it now and put a couple of tack welds to hold it there. With all of the neutral safety switches in there.. It has to be in park or neutral to start it now..
03-04-2010 06:15 PM
APalusky Which means?? I have a Lokar floor shifter. I had clearance problems with that lever on.
03-04-2010 06:10 PM
joe_padavano
Quote:
Originally Posted by APalusky
There is a lever just up from the bottom. I had to cut that lever off. When I was trying to put the mount on the cut off lever moved. That droped the works just a tad so that the clip would not fit back in the slots. I just moved it back over, and lifted the column tube over the lever. Everything fell back into place. The key turns,locks, and I am able to lock the steering column again..
The lever is for the backdrive linkage from the trans to the steering column. That allows the trans to lock in park when the key is removed. The system is designed so you cannot lock the steering column unless the trans is in park. With the collar rotated from the park position, the linkage inside the column did not line up.
03-04-2010 05:36 PM
APalusky There is a lever just up from the bottom. I had to cut that lever off. When I was trying to put the mount on the cut off lever moved. That droped the works just a tad so that the clip would not fit back in the slots. I just moved it back over, and lifted the column tube over the lever. Everything fell back into place. The key turns,locks, and I am able to lock the steering column again..
03-04-2010 02:30 PM
V8 Super Beetle I know on the steering column for my beetle, that if the shaft is too far in the u-joint it wont lock. Pull it out a little and it will. This some play in the column when it's out. You have to position it just right.
03-03-2010 07:55 PM
burnt olds
Quote:
Originally Posted by APalusky
Fixed it Myself..
what was it ?
03-03-2010 07:54 PM
burnt olds
GM steering column won't lock!!

key out right , lock position ?
the plunger that falls in the slots on that big black part held by the ring clip
may have fell out upside down .
03-03-2010 07:50 PM
APalusky Fixed it Myself..
03-03-2010 06:55 PM
APalusky
GM steering column won't lock!!

I was working on my steering column. It is a 79 Pontiac Grand Prix tilt. I have it out of the car, because I pout a new floor in my 37 Ford where this is the column for it. I had it on it's steering wheel. I had to remove that little clip at the tip in order to get a Mullins mount to fit. I wanted to lock the housing after getting the mount to fit, and it won't lock.. The housing spins in a circle, but it will not lock. I can't get the clip to pop back into those slots either.. Any idea on how I can fix this?? Thanks.. Al

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:46 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.