Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Tuning an Edelbrock I'm gaging!
User Name
lost password?   |   register now

Thread: Tuning an Edelbrock I'm gaging! Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2002 09:13 PM
wrenchturner sounds to me its your float level if your float is set to high its flooding it out by what you decribed hard stops or cornering causes your problems maybe setting or bad float this is just my opinion almost bet.or could be sticking needle valve

[ April 28, 2002: Message edited by: wrenchturner ]</p>
04-28-2002 04:32 PM
HotRodF100 My cam is almost, if not exactly, stock. Your description sounds interesting though. Are there any adjustments that can be made to the idle circuit other than changing springs? I got onto the Edelbrock website and I am in the process of printing out their carb manual...if I don't run out of paper or printer cartrige first!
04-28-2002 03:44 PM
Centerline Idle mixture may not be your problem. If you're running a healthy cam you may not have enough vacuum at idle to hold the metering rods down. Both Edelbrock and Carter sell spring sets for different idle vacuum conditions. If the metering rods aren't held down at idle the mixture will be pretty rich and will cause the gas odor you're talking about.
04-28-2002 03:01 PM
HotRodF100 I set my idle mixture by feel, crank it in until it stumbles then back it out until it's smooth. The carb only has 3200 miles on it but I'm sure that the guy who put the carb on took it out of the box and there you have it.
04-26-2002 05:53 PM
4 Jaw Chuck How is your idle mixture set? Use a vacuum gauge to set it correctly. Check your fuel level next and then replace the needle and seat if it is old and the float appears to be correctly set. You might want to see if the float is heavy if it is a phenolic type or shake it if it is a brass type.

That should get you started.
04-26-2002 05:48 PM
Tuning an Edelbrock I'm gaging!

I have a 600 CFM square bore carb on a pretty stock 350 Chevy with a manual choke. The motor starts right up and runs fine other than sometimes on a real hard right turn, the motor stumbles a little. The problem is, if I start this thing in the garage I can kill the whole family with the fumes!! I actually leave my garage door open for a while after I park in the garage to let out the fumes. Carbs are not my forte'..give me dirtbike carb and I'll struggle through Edelbrock I figured I'd ask the experts!! Anyone have any tips or suggestions for websites??? Thanks HotRod

[ April 28, 2002: Message edited by: HotRodF100 ]</p>

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:37 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.