Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> SBC valve spring retainers......
User Name
Password
lost password?   |   register now

Thread: SBC valve spring retainers...... Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-13-2010 12:00 PM
weedy64 I use Lordco a lot but only because my nephew works there (with applicable discount) and if he doesn,t know he listens to what I am saying so I get what I want. He is usually able to make me happy but when it comes to performance parts Mopac is a much higher volume place and much better selection and sometimes price.

Good Luck.
07-04-2010 09:06 PM
383SBC Thanks Weedy, nice to see another local on here Yea I will give them a try, it's just a bit out of the way for me since I live in North Vancouver but the Lordco over here is absolutely hopeless, I had to explain what a valve spring retainer was to the guy and in the end he still had no idea
06-30-2010 05:20 PM
weedy64
Lower mainland parts source

Maybe try Mopac Auto Supply for performance parts in Langley for a performance parts source. Their staff seem to have much more expertise than the average parts place.
06-27-2010 10:05 AM
383SBC Ok thanks guys I didn't realize that, ill take a retainer, valve, and locks down to the parts store and make sure I get the right thing. I don't have any part #'s, they are a little bit dated I think. I have 11/32 valve stems so those retainers could be 10 degree for 3/8 valves making my 7 degree 11/32 locks fit incorrect.
06-27-2010 06:09 AM
BOBCRMAN@aol.com Also possibly 3/8 retainers on 11/32 valve stem..
06-26-2010 10:48 PM
ericnova72 Sounds like you are using stock 7 valve locks, and the retainers are 10 type. 10 locks are roughly 1/16" bigger and have a slightly flatter angle, makes them wider at the top. 10 is pretty much the industry race standard now days.

There are also what is called Super 7 locks, these are larger at the upper end like the 10 locks are but are still the 7 angle, makes then bigger around at the lower end than stock 7.

Do you have a part # for the retainer you have, or measurements of what you have??
06-26-2010 10:16 PM
383SBC
SBC valve spring retainers......

Hey guys so I'm having an issue with these valves I am installing. It appears that the retainers have too large a hole on the inside (where the locks sit) for the locks I am using. When installed the locks don't seat in the retainer until about half way down the retainer and this is causing the retainer to contact the rocker arm since it is sitting too high. My question: is there different size inner hole diameters for SBC retainers and different sized O.D. locks that must be used together? From all the other heads I've seen the locks sit pretty much flush with the top of the retainer so the valve stem is exposed and the rocker clears the retainer. It appears I either need different retainers with smaller inner holes to go with the locks I have or larger O.D. locks to go with the retainers I have. The rockers should clear once that retainer is sitting proper, it is about an 1/8" too high right now. Any info would be very helpfull because the parts stores around here don't even know what day it is.

Thanks,
Keith

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.