Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> help sewing a corner
User Name
Password
lost password?   |   register now

Thread: help sewing a corner Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-09-2010 12:37 PM
Coodeville Let me reclarify what I meant - the material was getting stuck in the welting foot itself - even though I was turning the wheel by hand. Part of the material was getting caught in the foot and I had to use a jewlers screw driver to smooth it out.
08-09-2010 11:57 AM
58 Delpala Thats what I ended up doing and thanks Dan the pictures did help after all. It just turned out to be such a deep pocket that it became alittle tricky but I got it. Pics will follow later tonite when I update everything I have done.
08-09-2010 07:53 AM
DanTwoLakes Nobody, not even experienced production line sewers, sews full, or even half speed around a corner, especially a sharp 90 degree corner. The way to do a corner is to sew up within a couple stitches of where you are going to turn, turn the wheel by hand until you reach the point you want to turn, lift the foot with the needle still in the work, turn the corner, let the foot back down, and then continue to sew.
08-08-2010 06:15 PM
Coodeville I ran into some trouble using the welt foot on the corner. The material got stuck. I found out that you have to be careful around corners. Turning the machine by hand was the best thing for me to do.
08-07-2010 07:17 PM
DanTwoLakes
Quote:
Originally Posted by 58 Delpala
Dan that helps alot but I was wondering if you have a between shot of what it looks like between pic #3 and #4.
Between picture 3 and picture 4 is just sewing to the end of the small piece. After that, I topstitched it so you could see it as flat as possible.
08-07-2010 05:07 PM
Rocketmanmh1
Hard to sew??

Hey, I see that you are only about twenty or so miles from me, I would be glad to show you how to sew the seam. If you would like my help just pm me and I will give you my email.
08-07-2010 12:52 PM
58 Delpala Dan that helps alot but I was wondering if you have a between shot of what it looks like between pic #3 and #4.
08-07-2010 11:39 AM
DanTwoLakes Here is the sequence of how to sew it together. Sew the long piece and the piece next to the long piece on the right together. Flip that assembly over so it's face up, and then sew the small piece on starting from the end and sewing toward where the long piece curves to the right. If the piece is slightly longer when you get to the end, just trim it off flush.

I didn't cut any relief cuts in the vinyl when I sewed it, but it's perfectly O.K. if you want to do that, just don't cut them too deep. Remember that the vinyl will be stretched onto the seat frame, so any wrinkles should just disappear.

I topstitched both seams so it's easier to see how they should look. The last picture is how the whole thing turned out. Sorry, this is the best I could do without having the pieces to make it exact.
08-07-2010 10:29 AM
58 Delpala
help sewing a corner

So After I got my inserts done I decided to cut up the original seat cover to get the patterns for the rest of the seat cover. Here is what the original looked like after I took it appart.



And here is the new pieces ready to sew together. The only problem is the opposing turns in the pieces and here is where I am at right now.



So when I try to bend everything to get the seams right it gets these nasty wrinkles and I cannt get it in the machine. Any suggestions other then hand sewing it LOL. Keep in mind this is the bottom of a bench seat for a 58 Chevy. That part is the end part at the rear of the bench where the cover folds down to cover the sides.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.