|08-24-2010 07:32 PM|
stroked a 305
I can't imagine duplicating the mileage again but I'd like to build one for myself. Practical having something that will work cheap... and run too.
Most satisfying results of any small block I ever built. including 400 based stuff.
|08-24-2010 06:54 PM|
|RaticalRods||I think ill try the xtreme 4x4 262 cam, it seems like the right direction for me, its definitely got the torque i need.|
|08-24-2010 02:15 PM|
|08-24-2010 11:10 AM|
|BigRoy1978||not trying to bash...but to get good power out of this motor is gonna need compression. Not saying its not possible, 305 Sprint cars out here get around 600+ hp from thier 305's...but they have some work done to them...A LOT of work...|
|08-24-2010 11:01 AM|
flat top pistons are being put in, so around 9:5:1.
and thanks for the heads up on the rpm range, ill take a look at that.
|08-24-2010 09:26 AM|
|V8 Super Beetle||
If you take a look at that build link I posted, you'll see that the XE268H cam they used made best power at 6,100 rpm.
|08-24-2010 09:25 AM|
|08-24-2010 09:09 AM|
|RaticalRods||stall is stock, well a v6 stock stall and gears are stock but sorry no idea what they are..ill have to jack the truck up to determine that.|
|08-24-2010 08:49 AM|
ok, no idle isnt what i am aiming for, just would like a noticeable change. The heads are stock but have heavy springs on them and the pistons are flats, it was estimated that it would be close to a 10:1 cr.
If the xe262 is the way to go then ill do that, i was just ready about how the 270h was an older design and liked higher cr, thats why i was leaning towards that grind. Thanks for the input.
|08-24-2010 08:03 AM|
|08-24-2010 07:16 AM|
We're right back to what heads (and thus what CR) are you going to use? What gear ratio and stall speed?
If it's stock heads (should be 58cc not 68cc), I would NOT run anything any 'beefier' than a Comp 262 in your C-truck. Forget about the idle sound, unless that's ALL you want and to drive a pig otherwise.
|08-23-2010 10:18 PM|
i think i am leaning towards a comp cam magnum:
Magnum 270H Hydraulic Flat Tappet Camshaft & Lifter Kit
RPM Range: 1800-5800
|08-23-2010 08:55 PM|
|RaticalRods||Yeah sounds like fun, i cant wait. I am only looking for a cam because i need to buy one anyways, so i figured id go as big as possible with this set-up because honestly there isnt really a money difference between a stock cam and a little beefier cam.|
|08-23-2010 08:02 PM|
|American Muscle||I have an 86 chevy C-10 with a nice little 305 in her. Not a street/strip but fun to drive and turn a few heads. All i have is headers, edlebrock performer intake, edlebrock 600 carb, 700r4, and most inportant i got a set of gears(3:42) and this thing flies. I wouldnt do anything internally to a 305. Now I have seen some pretty wicked sounding cammed up 305's but that same cam would do lots more in a 350. If thats all you have then roll it.|
|08-23-2010 07:19 PM|
ok well i think iam sticking with the heads that came with it, they held a .480 lift cam before it was torn down, the springs were replaced to hold that much lift and the heads are 68cc. So a little for information for my build.
That being said, with those heads and a 5.0l Edelbrock rpm II with 600cfm carb.
Any suggestions on a cam... i would like a rougher idle, good torque but also hp for a little track time (i know its not going to be turning stunning times, but id like it to do as well as possible)
|This thread has more than 15 replies. Click here to review the whole thread.|