Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Welding Help...... Floor Pan Replacement ? Experts Welcome !
User Name
Password
lost password?   |   register now

Thread: Welding Help...... Floor Pan Replacement ? Experts Welcome ! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-27-2010 06:29 AM
deadbodyman heres some of the bracing ...
I just used what I had laying around but found that electrical conduit works well ,just smash the ends flat and run a 10mm drill screw it.No need for welding.You'll also need a screw at the intersection of the X.
You'll want to replace or repair any worn hinges first then adjust the door gaps.
Put your braces on the inside of the jamb so you can open and close the door ,this way you can monitor any movement when your cutting and welding..
The bracing I did here is way more than you'll need because I replaced the floors and rockers also dropped the body over the frame..
if your only replacing the floor theres no need for a brace connecting the front and rear pillar ,the rocker will do that.All you really need is an X in the jamb but extra bracing never hurts.
Send pics of your progress as you go...
08-27-2010 05:44 AM
deadbodyman heres a couple ....put them under the rear axel and under the control arms where ever it fits best usually by the ball joint,,,
This way its just like the car is sitting on the ground ....
08-27-2010 05:28 AM
mustangsal Check the pics. On the front you want to be on the lower arm toward the wheel. It may even have the stock jack point there. In the rear you want to put them under the shock plate (where the rear is bolted to the springs and the shocks attach).

Pics are from a Mustang, but yours should be similar.
08-26-2010 06:54 PM
outoftouch Can someone show me a picture of this rocker bracing/diagonal ?

Also, exactly where "deadbody" says to place the jack stands ?

Pictures are worth a thousand words as they say !

thanks
08-25-2010 10:56 AM
OneMoreTime Is that car a unibody like a Mustang..if so do all you can to support the car and put the temp bracing in like Joe suggested. Make sure the doors are right before welding anything..

Sam
08-25-2010 09:09 AM
joe_padavano
Quote:
Originally Posted by outoftouch
Need some ideas thanks
The only way to ensure that there is no movement is to temporarily weld side-to-side braces between the rockers. I would also add a diagonal brace to ensure no racking.
08-25-2010 06:43 AM
deadbodyman I like to get the car as high as I can and use the stands under the suspension so the weight of the car rests on the suspension,just as it would normally ...Its very important with a uni body...and a good practice with full frame cars too...I've had the door gaps close or get wider on a few hardtops and most convertibles even with full frames,so just put the stands under the suspension just in case... and be safe...
08-24-2010 06:50 PM
outoftouch
Welding Help...... Floor Pan Replacement ? Experts Welcome !

I am about to replace my floor pans to a one piece ( 65 Satellite) before I finish cutting out the remaining floor what are some good tips for securing the car from twisting ?

Some say that as long as the car is on wheels under it's own suspension load that I should not have any worries. Basically, I can take out the old floor and then measure fit and weld in the new one piece.

Then others say to put it up on floor jacks to release suspension ?

Which is reality ?

I am just doing it my garage, I have no special gear, other than floor jacks, jack stands etc...

Need some ideas thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.