Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 502 HO idle RPM
User Name
Password
lost password?   |   register now

Thread: 502 HO idle RPM Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-03-2010 04:23 PM
rajsid
Quote:
Originally Posted by cobalt327
I bet that 502 woke it up- what trans do you have?
M21 4-Speed Manual (close ratio)
09-03-2010 12:14 PM
cobalt327 Nice ride! My brother in law had a '68 4-speed w/o T-tops about that same color, w/a 400 HP 427. I had basically the same engine in a '69 Impala SS 427 w/TH400 rated @ 390 HP.

I bet that 502 woke it up- what trans do you have?
09-03-2010 11:30 AM
rajsid
Quote:
Originally Posted by cobalt327
14 BTDC sounds pretty good. You might even go for a little more, but you'd need to limit the mechanical to keep the total where it needs to be.

I didn't find an initial timing rpm spec, either. That's why I thought the 800 rpm spec that the Ramjet uses might suffice.

But as long as there's no mechanical advance sneaking in on you and the vacuum is disconnected and plugged, you're good to go.

Good luck.
Cobalt and Bryan,
Thank you so much.





09-03-2010 10:46 AM
cobalt327
Quote:
Originally Posted by rajsid
You are right, I think the key is to keep the rpm low enough that there is no mechanical advance.



The engine is timed at the 502 HO spec. I am getting 3600 @ 36 with the vacuum disconnected. The dist that I am running gives 22 degrees of mechanical. So 36-22=14 is the initial timing that I have set to. Nowhere can I find any reference of the initial RPM.
14 BTDC sounds pretty good. You might even go for a little more, but you'd need to limit the mechanical to keep the total where it needs to be.

I didn't find an initial timing rpm spec, either. That's why I thought the 800 rpm spec that the Ramjet uses might suffice.

But as long as there's no mechanical advance sneaking in on you and the vacuum is disconnected and plugged, you're good to go.

Good luck.
09-03-2010 09:53 AM
rajsid
Quote:
Originally Posted by cobalt327
If for some reason you find that there's advance coming in even at a low idle, you will need to add a heavier advance spring to prevent this.
You are right, I think the key is to keep the rpm low enough that there is no mechanical advance.

Quote:
Originally Posted by cobalt327
36 total @ 3600 rpm, with vacuum advance disconnected.
The engine is timed at the 502 HO spec. I am getting 3600 @ 36 with the vacuum disconnected. The dist that I am running gives 22 degrees of mechanical. So 36-22=14 is the initial timing that I have set to. Nowhere can I find any reference of the initial RPM.
09-03-2010 09:19 AM
cobalt327
Quote:
Originally Posted by rajsid
Does anyone know the factory recommended idle RPM for a 502 HO motor is?

I was told that the initial timing should be 14 degrees. I am trying to find out at what RPM should I get 14 degrees at.
If you are using a mechanical advance distributor, just be sure that the rpm is low enough that the mech. adv. is not adding any advance. Disconnect and plug the vacuum advance like Brian said and you will be fine.

If for some reason you find that there's advance coming in even at a low idle, you will need to add a heavier advance spring to prevent this.

The Ramjet 502 is:

Ignition timing: 8 BTDC @ 800 rpm; 36 total @ 5000 rpm.

You can compare your cam, etc. to it to see if the 800 rpm should also apply- but I would say it should be a good rpm to use.

FWIW, the 502 HO uses (what is shown in this particular spec chart):

36 total @ 3600 rpm, with vacuum advance disconnected.

The HT 502 uses:

Ignition timing: 4 BTDC
09-03-2010 06:24 AM
Bryan59EC I have a 454HO in the 59
Disconnect the vacuum advance and set to 16 as low an RPM as possible

I run 16 initial and at 2500 I am about 36-38-----with the vacuum advance hooked up I am close to 50* at 2500.

I have a manual trans so my idle is set at 750, altho many set their
BBC idles at 900-1000 with automatics

What kind of vacuum are you getting at idle-----me--only about 10
09-03-2010 12:43 AM
rajsid
502 HO idle RPM

Does anyone know the factory recommended idle RPM for a 502 HO motor is?

I was told that the initial timing should be 14 degrees. I am trying to find out at what RPM should I get 14 degrees at.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.