Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> I need a spindle for a 47 Ford pickup
User Name
lost password?   |   register now

Thread: I need a spindle for a 47 Ford pickup Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-22-2010 11:17 AM
re;'47 spindle

Bonus thought,the old kingpin makes a great drift/driver. don't chuck it. the old skool way to pop it was to take 2 large hammers place one against the back of the stud hole and whack from the other side,just be sure to wear eye protection! tom
09-21-2010 08:36 PM
enjenjo Normally you would clean any rust off the spindle before assembly. If you didn't, take it back apart and do it now. Also repack the bearings.
09-21-2010 12:47 PM
1F9O4R7D Anyone have any imput?
09-16-2010 12:04 PM
1F9O4R7D I finally found some time and completed the job. just one thing odd though the new bearing/grease seal and nut will not go onto the spindle enough so I can put the cotter pin back in the axle. I am assuming the little rust that is on the new spindle is causing this. I am thinking if I drive around for a bit then try to tighten the nut, maybe the surface rust will waer off.
I am certain the new spindle is the exact one I need but the diameter of the axle is slightly enlarged by the rust.
Any comments?

Next project I have to adjust the drum brakes. What is the best way to do this front or back first?

09-12-2010 04:35 PM
Originally Posted by 1F9O4R7D
I got the kingpin out and the spindle off the axle but I can't get the spindle off of the steering arm. It is a ball joint connection. Does this need to be pressed out?
ALSO ... the tie rod end will screw out of the drag link. They come in right hand threads and left hand threads ... depending on which side they are installed. They are available new ... for mot much $$$. I believe I would consider replacing them ... while you are this close.

09-12-2010 08:32 AM
trees Not sure about that newer style king pin, but most have a locking mechanism, such as a bolt into a grove/dimple in the king pin. Remove that an it should come out relatively easy. A new king pin and bushings should be in order as well.

09-11-2010 08:06 PM
Deuce You need a pickle fork ... a special tool made for separating the two.

Most of the chain-type parts stores ( Auto Zone/ Advance / O'Reilys ) have a tools loaner program and they have this tool in that program ( usually )

They are not that expensive to buy ( I have a old Snap-On one that I got a a yard sale 20/25 years ago for 5 dollars. If you were close ... I would let you borrow it
09-10-2010 02:50 PM
1F9O4R7D I got the kingpin out and the spindle off the axle but I can't get the spindle off of the steering arm. It is a ball joint connection. Does this need to be pressed out?
09-10-2010 02:12 PM
1F9O4R7D Thanks Deuce Dick's shop was able to provide me with the right part.
09-10-2010 02:11 PM
1F9O4R7D I got a new spindle but I can't get the old one off. Does anyone know a trick to removing the kingpin?
09-08-2010 12:26 PM
1F9O4R7D The spindle is stamped "21A" I have to start looking around.

The spindle and the axle appear to be one piece. how does this thing come off?
09-07-2010 06:00 PM
enjenjo Deuce is correct, the 42 to 48 car spindle is the same. The F1 spindle is different.
09-07-2010 12:37 PM
Deuce I believe a 42 to 48 car spindle is the same ... but I could be WRONG

I would call Dick Spadaro ... he sells parts, is very knowledgeable and most of all HELPFUL.

Tech Line: 518-861-5367

He is in New York state.

I have a couple pair of 48 to 52 F1 spindles but I do not know if they are the same as yours. I just started messing with the newer stuff ( like late 40's ) recently.

Here is my current project.

It is a 1949 Mercury 1/2 ton pickup.
Only available when new in Canada.

09-07-2010 12:12 PM
I need a spindle for a 47 Ford pickup

I was coming home at 0230 this morning and a wining started in the front end. I slowed down to about 20 mph and something popped. As I stopped the front drivers side wheel popped off. After towing the rig home I discovered that the outer wheel bearing seized up and the spindle snapped off just before the threads. Well I am thankfull to be alive and thankfull there was no further damage but I am pissed. I need help locating a new stock spindle for a 1947 Ford pickup. Does anyone know where I can find one. If I have to buy a pair of drop spindles I will but I would rather just replace the one.

Thanks guys!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:36 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.