|01-05-2013 09:19 AM|
|SHOPIE||Thanks! I did note the one on the right locked a cog looking thing on the shaft underneath the bed. I will take up reading the manual in front of the machine this weekend. I appreciate your help!|
|01-05-2013 08:02 AM|
This is not a Singer 111W, it is a Consew 226R, but they are almost identical machines. Are these the buttons you're referring to? If so, the one on the left is to change stitch length, and the one on the right is to re-engage the safety clutch on the main shaft under the bed. The safety clutch disengages when you jam the machine. It prevents further damage to smaller more sensitive parts.
BTW, the manual for the 111W152, 153, 154, and 155 will work for the 151, there are only minor differences between all of them.
|01-04-2013 07:54 PM|
OK,so Singer does NOT have the manual for this machine. I don't think I need many parts and I can find them with that parts list. However, there are some buttons on the throat plate I have no idea what they are for. They seem to engage into parts on the drive shaft underside of machine to stop different mechanisims. I am assuming they might be for setting timing or some other mechanical repairs. They are not the "oiler" spots for the old oil tin can... anyone know?
|01-03-2013 12:02 PM|
|DanTwoLakes||Here is a link for the parts list and diagrams: Sewing Machine Manuals, PDF Sewing Machine Manual Parts Books and Instructions|
|01-03-2013 11:16 AM|
|SHOPIE||Singer (1-800-474-6437) is constantly busy (frustrating) the model is not found on that site. I am looking for info so I can find out what all is missing from my machine so I can restore it.|
|01-03-2013 10:26 AM|
The needle action you are describing is the needle feed part of the compound feed system that the 111W151 has. The other part is drop feed, which is accomplished with the feed dogs.
The term "walking foot" is a term to describe alternating presser foot, which is the correct term. Your machine has three shafts, one of which holds the needle and the other two shafts hold one part of the foot. When one of the foot shafts goes down, the other goes up, hence the name alternating presser foot.
You will have better luck with the web site www.singerco.com, which has some instruction manuals available for free.
|01-03-2013 10:02 AM|
New to me.... the needle operation on this machine is different. Instead of just going up and down, this needle "walks" the project thru the machine, so the throat plate has a slot opening in it, not just a singe hole. The needle pierces the fabric and travels in conjunction with the feed dogs, moving the project one stitch back, and then returns into the start of the next stitch. Therefore, the extra feet that the seller provided me is NOT for this machine, which are also in the catalog previously (therefore erroneously)mentioned. Therefore, I guess you could call it a "walking needle" as opposed to a "walking foot".
|01-03-2013 09:34 AM|
I have sewn many a car seat, snowmobile seats, motorcycle seats with a Singer 31-15, which I much prefered over my Juki walking foot. I have just purchased a 111w151 to do a camper interior.It will need parts and work, first. If someone is doing a few projects, then sure what he has will work, I think. Upon inspection of my machine yesterday, I saw and then realized the problem with the foot that was encountered. It is not typical. Also, the bobbin is a very tight fit, so I could see the request on that. Waywak had the regular everyday feet, but I did not realize the configuration of the 111w151 foot, as that machine is at my shop, and my computer is at home. I did not intentionally give out false information. I was not implying a home owner machine would do the job, as I know that it never would!
When using a straight stitch machine, and you have to jump over multiple layers, stop the machine and hand spin the wheel over the lump so that you do not break the needle. Singer Co., in the past, has been very helpful to me, they even sent me a bound copy of "historical records" full manual and repair book for my 31-15, which I should never have sold when I moved. So, ok, I should have examined my machine before I posted a reply, you DO know more than me, so I'll leave future replies up to the expert. The previous owner handed me a manual, but I later saw that it was for the 111w155 not 151. I intend to call Singer today so see if they can get me the correct paperwork I will need to restore the machine. I look forward to learning from this site.
|01-01-2013 08:48 AM|
|DanTwoLakes||The problem is not the thread or the needle. What he has is an industrial sewing machine, not a home sewing machine which is what wawack sells parts for. Advising someone that they don't need a walking foot to sew a car interior is not good advice. There is no add on or accessory that can make a non walking foot machine into a walking foot machine. Also, most industrial machines are compound feed machines which means that they have two feed systems that work together. You can't replace a compound feed, walking foot machine with a home machine which almost always have needle feed only, and never have a walking foot. That's like comparing a .22 to a howitzer.|
|12-31-2012 07:56 PM|
|SHOPIE||I have the manual. It says to use left twist threat for the needle, either for the bobbin. It is important that you keep the machine oiled to operate properly. You can get feet at www.wawak.com, and just check the configuration of what you have (shank) to get the right ones. www.singer.com will get the phone # (1-888-873-9822) and they are usually very helpful. Don't worry, your foot will get lighter the more you use the machine and before you know it, you'll even be able to use it that fast. btw, you don't need a walking foot machine for thick stuff! You get "the hump jumper" $2.99or the "jean-a-ma-jig" $1.55, both are for use on all heavy fabrics, to stitch over bumps without breaking the needle.Also, www.sewingmachineparts.com/singermanual.|
|12-31-2012 03:41 PM|
I can't see anything wrong except it looks like the bobbin thread is not under the tension spring on the side of the bobbin case, which would make the bobbin thread looser than the top thread.
I can also tell you that about 99% of the time it's something you are doing wrong and it is not the machine.
|12-31-2012 03:38 PM|
|Coodeville||Is it possiblethat some dust and dirt got into it while it was inactive ?|
|12-31-2012 12:46 PM|
So, I've completed my boat upholstery project. It came out great. I then left the machine and I need to use it again for another project. It was working fine when I left it, I don't know what could have happened.
I'm having an issue where the top thread is breaking on the third stitch. I took a video of this happening. I have tried adjusting both the top and bottom thread tensions but something doesn't look right when it's running.
Can anyone see what the issue might be from the video?
|09-27-2010 07:54 PM|
|09-27-2010 02:29 PM|
|Coodeville||I got mine on eBay as well. How can you beat it? It goes right to your snailmail box.|
|This thread has more than 15 replies. Click here to review the whole thread.|