|02-19-2011 11:45 AM|
Ayuh,... I use Martin Seynor Prizim paint system,...
You can read about, 'n see the results Here...
|02-18-2011 11:59 PM|
|02-18-2011 11:26 PM|
|bigbee||Using automotive single stage for the top and bottom works great and is easy for the first timer. We've got customers with100 mph base coat clear coat that where painted 20 years ago and have held up great. Personaly I like ppg concept single stage. It pays to use good paint|
|02-18-2011 07:45 PM|
|10-10-2010 09:20 AM|
this is my boat , bought it in a boat junk yard in '02 in '04 it was in hot boat mag.
|10-10-2010 09:11 AM|
ok I have painted MANY jet boats just finish the bottom on this one yesterday, blueprinted the bottom speed coat added,
I painted my boat 8yrs ago and have been in the water every weekend, and it does well over 80 mph with no problems with paint failure, if you need any pointers or advise PM me, I don't wanna step on no toes here..
|10-05-2010 09:49 PM|
I guess you would have the boat in the water and mark the waterline. Remove the boat from the water. When painting the bottom bring the color an inch or two or three above the waterline mark. A bootstripe if you want.
On the epoxy bottom paint, there is what is called an epoxy barrier coat that is applied over the bare fiberglass(polyester resin) to help prevent osmosis through the fiberglass hull. Many times this barrier coat is used after blisters in the fiberglass boat bottom have been repaired and also for added protection. Then the barrier coat is overcoated with bottom paint.
But yours, S10, will stay mostly on the trailer so an epoxy barrier coat is not necessary.
Hope this helps.
|10-05-2010 09:32 PM|
Have witnessed some amazing results with Interlux Perfection rolled and tipped on the topsides. The prep work directions on the can is most of the work. Have not witnessed but have heard it once that to touch up spots on the finish if you get a scratch is a bear.
Graphite mixed with epoxy on the boat bottom gives great abrasionn resistance; comes out black though. Or copper powder mixed with epoxy for antifoul and that classic gold/copper colored bottom.
If your up on blocks it's easy to just move a set of blocks and paint that area of the bottom.
Sounds like a great boat. Best of luck with the outcome. Hey ! No pictures. You should know you gotta post pictures.
|10-02-2010 08:40 AM|
|cboy||Thanks Barry and Sam.|
|10-01-2010 07:07 PM|
|BarryK||Not talking about epoxy but paints made out of epoxy for bottom paint, two different things.|
|10-01-2010 04:59 PM|
|S10 Racer||Thats all great info and I appreciate it. My boat is very low profile and the water line is only about 6-8" below the transom sitting still so to make the job easier, I would probably paint the top with the same paint as the bottom. My boat don't have dock bumpers so there's really no stopping place to change paints anyways. So, from what I'm reading, it's better to use a non-epoxy paint on the bottom? Can you explain why this is? I would have thought that epoxy was the next best thing to gel coat but I don't know, I'm asking. You guys have more experience than I do with this so I'm willing to listen, just explain.|
|10-01-2010 10:50 AM|
If I were to paint those boats S10 would get a top shelf Single Stage on the bottom up to the waterline and then a base clear on the topsides in his choice of color or colors.
On Deweys his gets a marine bottom paint as his stays in the water all summer and his topsides would get a top shelf base clear on the topsides.
On both boats I have become partial to using a spray in bedliner material in the interior areas and then shooting a semigloss non glare material to cover the black bedliner. Too bad bedliner is not available in a marine gray for the boat guys.
Always I remove every item that is easily removed as one will find out just how difficult it is to mask and sand around all the hardware found on a boat. Seems like a lot of work to pull the motor and out drive unit, docking gear, windshield, guages, controlls and all that but once one starts masking and sanding and prepping around all that stuff one realizes the wisdom of just taking it all out of the way..
As usual just my opinion and your results may vary..
|10-01-2010 09:12 AM|
Any of the non epoxy based paints, that are made for under water, will work pretty good, rule of thumb is use non-epoxy type paints below water line if bot is not going to be in water more then three months at a time, although most paint would go six months without a problem, if you are using a good grade.
Another general rule of thumb is if that boat goes 80 or faster, best to have an SS below the water line, this is just a general rule that has been used for years.
Two of the best, since Imron is no longer imron, is the glasuit HD SS or the PPG Concept, a little more money then some that were mentioned but worth it if boat will get any abuse.
The best of the best was Durathane (ppg) but I'm not sure its even made anymore.
Above water base clear is great and will last longer.
|10-01-2010 08:52 AM|
Very timely question S10. I'm considering a new paint job on my bass boat/ski boat (pictured below), so I've been having many of your same concerns. Not to divert your thread too far, but I have a couple of additional questions.
I'm thinking of just painting the top of the boat (the area above the belt line/bumper strip). My boat stays in the water, at our dock, all summer long. But since I am only painting the area which is out of the water, can I use an automotive paint or is there a better alternative among the products which have been suggested for S-10? Keep in mind, this boat sits out in pretty harsh conditions in terms of sun (UV bombardment) and rain.
Also, I'm assuming I will leave the engine and all the associated mechanical gear installed and just mask it off to paint around it. Is that acceptable practice or should I really consider pulling the 135 Merc off the boat completely?
Any other general things I should be aware of when painting a boat vs painting a car?
|10-01-2010 04:54 AM|
|S10 Racer||Thanks for the replies all. The boat will not be kept in the water except for maybe overnight. I usually put it back on the trailer after everyday use.|
|This thread has more than 15 replies. Click here to review the whole thread.|