Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> primer test spray...new gun...2 thick
User Name
Password
lost password?   |   register now

Thread: primer test spray...new gun...2 thick Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-11-2010 06:21 PM
ozziesstang Finally layed down a couple descent coates of primer and since it was such a nice day out today....I sprayed first coat of bace coat. Came out very nice...no fish, no shrinking...just need to hone the pattern while spraying. Just finished sanding with 400 and will try a second coat tomorrow afternoon. Then...Im going to read up on here about clears.
10-04-2010 05:42 AM
deadbodyman Maybe it'll be ok for the primer try the 1.2 for the base then the 1.4....
...for the clear the 1.4
All those tip sizes make things more confussing for a newbie...I use a 1.4 for base and clear but its is a little small for primer if its not reduced a little.
10-03-2010 08:02 PM
ozziesstang Is 1.8 too big for primer? I also have a 1.4 which I planned to use on base and a 1.2 for clear. Should I change nozzles?
10-03-2010 05:29 PM
deadbodyman Ehat tip sounds awefull big ..thinning the primer might make things worse.and it might be too big for the base alltogether
10-03-2010 04:44 PM
ozziesstang I would like to avoid the runs too lol. I will test it once more at 4:1:1/2...and see how she does. Hope to have 2 coats of prime on by thursday evening, and get the base on next weekend. Thanks guys
10-03-2010 01:00 PM
southernculture I just finished priming my nova with axis versaprime 2k primer. I believe it is similar to what you are using. I mixed it 4:1:1 and it was a bit thin. I had alot of runs, not a big deal but would rather spend tomorrow not sanding runs. If I were you I would not thinning as much! My mix instructions were 4:1:1 with a 1.4 mm tip.
10-03-2010 09:58 AM
ozziesstang This is an OMNI high build primer. The sheet suggest (on second look) a
4: part primer to 1: part reducer to 1: part hardener. I swear I didnt see that the first 3 times I read it lol. I will get the MR reducer tomorrow...hopefully that will thin her up some. And thanks for the air advice. I Had it set at 25 lbs to the gun as a guess to the cap, but will kick it up a few lbs.
10-03-2010 04:48 AM
SuthnCustoms I think he was reffering to the tech sheet's recommended tip pressure at 8 psi,not at the gun itself.

Any time a tech sheet reccomends a pressure setting in the gun is usualy the tip pressure for spraying for a reference on what type of gun is best suitable for spraying the material..since just about any different type of gun will spray differently with inlet pressures they can't reccomend an inlet pressure.

I would read the tech sheet again and see what type of reducer is best compatable with it and how much it can be reduced for a better spray,then test some more panels and adjust the gun untill you get the best spray pattern and good lay.
10-03-2010 02:09 AM
cjperotti All 2k primers can be reduced 10 percent with thinner. 8 psi is a really low for any primer. Suggest you bring it up to around 29 psi and adjust from there.
10-02-2010 08:35 PM
ozziesstang
primer test spray...new gun...2 thick

Hello...Im ready to spray first coat of primer on prepped truck. Using a new Eastwood concours gun with 1.8 nozzle at 8lbs per I began testing and adjusting the gun and got heavy (thick) results. Followed teck sheet for the MP383 SV high build primer with MH284 hardener at 4:1 ratio. My question is...although the cut sheet doesnt mention thinning the mixture...should I? and with what? Also if anyone is familiar with the gun EW part # 51550.....any tips on adjustments? Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.