Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> holley 600 carb specs for my weiand 671 . HELP !!!
User Name
Password
lost password?   |   register now

Thread: holley 600 carb specs for my weiand 671 . HELP !!! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-11-2010 01:56 PM
mustang 671 also i have a tube coming off the base under the primary float bowl. it goes into the butterflys on the bottom of the carb . is this a tube for my vacum hose for my manifold ? if not whats it for ??
10-10-2010 02:10 PM
mustang 671
holley 600 carb specs for my weiand 671 . HELP !!!

hi all. have been working on my car all day. dumped the old fuel and cleared the lines and re filled with 99 pump gas . i have 2x vac secs 600 holleys on 671 weiand on 351w. this is what i have

-secondary springs are colour purple
-i have prefix 70 jets in both primary metering blocks and 1 of the sec metering blocks as the other cannot be fitted due to no room
-power valves have prefix 65
-acc pump cam is colour orange ( i think, as i havent seen the shade of brown) not sure which position it is in.
-diapghram on the acc pump is colour green ( not sure if they have different ones ?)

so my question is are there any changes that i need to do that are obvious at this stage ? i need to order some bits from holley this week so can always order some other bits from the reccomendations from you all. i have previously set out my engine specs in a previos post (671 weiand blower 351w engine) i have a high lift crane cam. 7.48.1 cr. blower underdriven 13% so hoping for around 6-8 psi to begin with.

i have set my inital timing at 12d btdc and total at 28d btdc all in at 3000rpm.
does this sound about right to get it started and running so i can run in my cam. its a fresh engine and only has had 5 min or running time so far.

had timing issues previous which i hopefully have got better to start with. i have a omex ecu that is open to be played with . so i can put in what figures i want,

it starts at 450 rpm on the bottom scale and the side scale going up is engine load from 1% to 99% . the rpm goes up by around 400 rpm for each incrament.

i.e

99
89
79
69
59
49 i can put any degree figure in this table
39
29
19
09
01
450-850-1200-1600-2000-2400-2800-3200-3600-4000-4400-4800-5200

what do you think as a start before i go to the dyno so i can run it in for 500 miles

thanks guys

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.