Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 327 in my 50 chevy truck?
User Name
Password
lost password?   |   register now

Thread: 327 in my 50 chevy truck? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-25-2002 01:15 PM
solowookie I'll have to check it out - I've been trying to get the casting # if the front, but I just can't read it good enough. I've got a few things I'm going to try to get it, and otherwise I will have to get it off the back of the engine after I pull it.

truck is a 66, and I'm sure the engine is original.
04-24-2002 09:18 PM
Studebaker Is the 327 a small journal crank or large journal?
I actually prefer the earlier 327 small journal crank engines, they have forged crankshafts while later 327's had large journal cranks that are cast. The cylinder casting #'s are important too. You might have a diamond in the rough with the right casting numbers. I think you will find that the 327 will surprise you with the power output. They have a better stroke / to rod ratio than a 350. 327's have a 4.00 inch bore by 3.25 inch stroke. If it is a small journal engine make sure you replace the rod bolts. The factory small rod bolts were weak for higher power ratings. Sounds like it's going to be a nice rod!
04-24-2002 08:08 AM
solowookie used desktop dyno 2000 - let me know what scenario's you want to try, and I will try it for you. send me an email.
04-23-2002 07:11 PM
WoodsEdge I am building a 50 Chevy Panel truck in which I plan on using this combination, 327 with 350. I have already installed a Mustang front suspension and plan on using a GM 10 bolt rear, I have one so why not use it. Where did you come up with those dino figures? Sounds like the performance figures I am looking for. What cfm carb and what pistons did you use? Thanks, Jack
04-22-2002 07:31 PM
solowookie LOL - yea I kinda have a problem with that right foot thing too! actually if I could get around 15 MPG with this thing I'd be very happy (that is when I was driving it go get good milage).
04-22-2002 03:05 AM
Tom I ran a 327 in my vette and got around 12mpg had 355s in back with 275/60 tires, auto trans no a/c a lunati cam 650 holley and factory alum mid rise intake(1966)also used headders and 2.5 exhaust with zip mufflers now if I happened to be going down a long hill I might have gotten as much as 18mpg... but the biggest problem with mpg is ,and you will probably find also, is that my right foot is atleast 4 and a half sizes larger than the left foot...so my suggestion is install the gas pedal on the left and mpgs will rise
04-21-2002 11:53 PM
dinger With a stock rearend, trans, your mileage would be pretty miserable, i would guess 12-15 mpg. Myself, budget minded, I'd go 70s Nova auto rearend, turbo 350 trans, tallest wheels and tires I could find for a decent price. Unsprung weight- tires, wheels, tire width would all be a factor. A Nova or Camaro subframe or Mustang 2 front suspension will lighten up the front and give more stopping power. Your truck is about as aerodynmic as a brick, you can't expect miracles but would definetely be a cool ride. Maybe around 18 mpg with something like this. good luck.
04-21-2002 08:03 AM
solowookie
327 in my 50 chevy truck?

OK guys...

I'm thinking about putting a 327 together for my hotrod; I can get the engine for free (and it would have some sendimental value). I'm thinking dart iron eagle heads with a comp cam extreme energy roller cam with roller rockers, and an edelbrock performer RPM electric choke carb with vac. secondaries.

would this engine get decent MPG? my dyno numbers;

RPM's HP Torque
2000 147 385
2500 189 397
3000 276 413
4000 317 415
4500 352 410
5000 375 393
5500 380 363
6000 368 322

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.