Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> What to use for welding protection / blanket
User Name
Password
lost password?   |   register now

Thread: What to use for welding protection / blanket Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-04-2010 08:04 AM
MARTINSR The welding blankets are pretty nice to have. I have a few smaller ones that I got somewhere (marketed for something outside of welding, can't remember what). They are so slick no tape would stick to them, some super nylon or something. Anyway I would hold them in place with magnets. But the last one I got is from a welding supply and it is really nice to have. It is comforting to know I can toss it over my car if I am welding near by and it won't scratch the paint but protect it from flying sparks.

I burnt up a seat on an almost new Honda years ago while using something I shouldn't have and I learned my lesson.

Even with the welding blanket you don't want to it to have any big wrinkles that a spark from the MIG can get caught in. Those little red hot ball will even burn thru the welding blanket! It won't start on fire, but it will burn into or thru the darn blanket. So keeping the piece straight and flat so these balls can roll off is my best advice.

And of course the better your welds are,the cleaner the metal for example, the less sparks you will have.

Brian
10-31-2010 08:19 AM
bondo Ayuh,... I use either a canvas tarp, or for smaller jobs, an old leather jacket...
10-27-2010 10:05 AM
V8 Super Beetle I like to use damp cardboard or a damp old towel.
10-26-2010 06:32 PM
LATECH Go to the carpet store and get some carpet samples to use. They are pretty fireproof as todays saftey standards for building materials are pretty good, I have used them for welding and they do OK. And they are free
10-26-2010 05:08 PM
carl_martha37
welding

I just find that old blankets work good. You do want to make sure that there is no oil or gasoline on the blankets. You also want to make sure that they are think enough. Other than that, you should be fine.
10-22-2010 03:41 PM
OneMoreTime Thosel cheapo blankets work fine and they are cheap so when they get all nasty and worn it is no big loss to toss em and get new ones..

Sam
10-22-2010 02:10 PM
evolvo If I need to protect something when I'm welding (mig) I throw some corrugated cardboard over it and/or on the ground. Clean corrugated boxes are a perfect source. They don't catch fire, sparks leave little burn marks.
10-22-2010 12:56 PM
alittle1 I think that was one of the reasons why you should use blankets, the sparks and tracers will stop because friction across the surface of the blanket and the ridges of the blanket. Have you looked at the one's PraxAir sells?
10-22-2010 11:27 AM
Ripped
What to use for welding protection / blanket

I checked at my local supplier, wher I get my tanks filled. They only have cheapo welding blankets.

I was thinking of (and will be) making a couple small sheets of thin plywood skinned with sheet metal, which I can use on floor areas, underneath.

Problem I see with that, is the sparks and blobs may still bounce off the sheet metal, and go elsewhere.

Any suggestions appreciated

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:41 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.