Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Piston Replacement Help
User Name
Password
lost password?   |   register now

Thread: Piston Replacement Help Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-28-2010 01:19 PM
Marshmellow When assembled the Piston sits approximately 1.5mm below Cylinder deck on TDC inside the bore. Would you suggest to just let the cylinder be and call it a day without worrying about detonation or gas octane? Because that would be absolutely wonderful if true.

Also how much would you believe It would hinder the performance of the engine if no corrections are made to the Cylinder?

I believe the Cam chain tensioner has enough travel left in it that it will tension the chain tight without any slack, the retard timing causing the engine to peak out at higher rpm's I can deal with as well, provided I am recommended to shave the cylinder, if suggested not to then both the above would become irrelevant.

The only confusion that keeps me right now is to shave the cylinder or not.
12-27-2010 07:22 PM
1800guy Maybe bike engines are different from a car engine - but if the piston is in good shape, why not sleeve the cylinder? A sleeve has to be cheaper than a good quality custom made piston.
12-27-2010 07:05 PM
matt167 send the specs to Egge machine, and they can make a new 1..replacement pistons that are otherwise unavailable is most of what they do
12-27-2010 06:36 PM
dgcantrellsr Wouldn't it be more feasible to order oversize and have it bored, if the pistons are wore I would assume the bore is also.


Quote:
Originally Posted by Marshmellow
My 1st thread here, be easy on me for asking the questions I do. :-)

So I'm actually working on replacing the Pistons on a old 4 Stroke 400CC Bike engine, the previous pistons are well over the wear mark. Upon looking up for replacement pistons sadly I came to know none of the manufacturers make the pistons I'm looking for anymore, wiseco etc.

So now the best replacement pistons I have found from a different bike engine look to be identical EXCEPT the pin to deck height which is a mm shorter than the original stock pistons. I can make up for the difference of height by shaving either the bottom base of the cylinder or the head gasket surface area. Now I'm just unsure if it will cause any issues in the stroke or performance. Also if I can go ahead with the shave idea, what would you recommended to shave, the base of the cylinder or the top?

Thanks.
12-27-2010 03:02 PM
Marshmellow
Piston Replacement Help

My 1st thread here, be easy on me for asking the questions I do. :-)

So I'm actually working on replacing the Pistons on a old 4 Stroke 400CC Bike engine, the previous pistons are well over the wear mark. Upon looking up for replacement pistons sadly I came to know none of the manufacturers make the pistons I'm looking for anymore, wiseco etc.

So now the best replacement pistons I have found from a different bike engine look to be identical EXCEPT the pin to deck height which is a mm shorter than the original stock pistons. I can make up for the difference of height by shaving either the bottom base of the cylinder or the head gasket surface area. Now I'm just unsure if it will cause any issues in the stroke or performance. Also if I can go ahead with the shave idea, what would you recommended to shave, the base of the cylinder or the top?

Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.