|01-08-2011 08:41 AM|
I think people may be missing the point of the electric fans. If your fans are running while you are moving, either your fan temp is set too low, or your radiator isn't big enough.. the fans are only there to keep the engine cool while the car is NOT moving. Once you get moving, the fans should be turning off so they don't restrict air flow. (if you don't use a controller, then it's different)
i have a 160 t-stat in my car, but I have my electric fans set to turn on at 200.
and the big fan switches to high speed at 220. This way they aren't constantly running. and I can stop briefly w/o the fans cycling on and off.
I set them up this way back when I had a little 80A alternator, and the electric fans would drag the voltage down. now that I have a 110A CS130, it doesn't make much difference
my one fan controller that turns both fans on together (with the big fan being on low) has an extra wire to turn the fans on when the A/C is on.. I don't have AC so I ran that wire into the car to a toggle switch.. so when I'm sitting in the staging lanes at the track, I can force the fans to run anyway to keep the engine temp down so I'm not trying to launch with the engine temps up near 200
|01-04-2011 11:36 AM|
You should expect that the engine will run from 10 to 15 degrees warmer than the stamped temp on the thermostat, the reason for that is the stamped temp is the opening temperature where the thermostat's valve just cracks open, it takes another 5 to 10 degrees or so to achieve full opening.
200 degrees on a 195 thermostat is what I'd consider inside the normal range of operation. If the electric fans can pull the operating temp to 185, I say they're pretty good as at this temp the thermostat is again closed and has to recycle to open again.
If everything else is doing its job, a 185 thermostat should get you a running temp between 190 to 200 degrees.
Don't forget these things are mass produced, their functional range is probably on the order of +/- 10 to 15 degrees. To a large extent the actual operating temp say 220 to 230 as a max isn't as important as keeping the insides of the cooling jackets wet. That's to say a running loss of coolant will be far more destructive than a wet though high operating temperature, with-in reason of course.
|01-04-2011 08:48 AM|
I always drill 3 1/8" holes in any thermostat that's going in a custom cooling system. Its cheap insurance against air pockets which WILL lead to premature failure of critical (and expensive) engine components.
"Aerodynamics are for people who canít build engines." Ė Enzo Ferrari
|01-04-2011 03:47 AM|
I pretty much proved that the other day.....when I took out the 195 and replaced it with a 180 thermostat. With the 195, I was running around 203 degrees with the fan on. Put in the 180 (fan on) and it dropped to 188-189 degrees same road, same time and same conditions. I was taught the same way....after it opens it doesn't have anything to do with the running temperature. I have changed my line of thinking after doing the 180 switch and talked to a certified GM mechanic the other day. He says that the degree does determine how low it will cool before the thermostat starts closing and will hold the temperature so it goes no lower than the stated degree for that particular thermostat.
I do appreciated everyone's replies~~~~~~Ron
|01-04-2011 02:22 AM|
You're in Florida, try a 165 or 180 thermostat. Check your radiator cap to make sure it is good and of the correct lbs. Run a 50-50 anti freeze-water mix. Set your fan to come on earlier, maybe 185-190 max. Are you running a fan shroud? They do work! I would not waste time drilling holes, once the thermostat opens, after warm up, they don't serve any purpose. Good luck! Bob
|01-03-2011 05:16 PM|
Stewart performance does it has the holes in the thermostat they sell.
And i read somewhere where ford did it in the windstar van also.
|01-03-2011 04:04 PM|
If drilling a hole or holes in a thermostat was a good idea, why don't the manufactures do it, and advertise it as "new and improved," "high performance", or some other bs?
They could charge a higher price for it if it were a good idea.
Some have a very small hole around 1/16" with a loose rivet in it to restrict the flow of air even more.
So the fact that the manufactures aren't doing it should tell us something.
|01-03-2011 01:49 PM|
|machine shop tom||
|01-03-2011 11:28 AM|
|01-03-2011 09:03 AM|
|XNTRCI-T||I drilled my stat, too. My understanding is this is mainly to allow air to escape the block when filling the system. I would think the amount of coolant flow through such a small hole would be insignificant.|
|01-03-2011 07:41 AM|
I always drill one 3/16" hole when I install a t-stat, any more than that and you're defeatting the purpose of a t-stat, anyless and you can get air pockets.
High system pressure, high flow, about 30% antifreeze has always worked very well for me.
|01-03-2011 06:16 AM|
This is copied and pasted directly from Stewarts Water Pumps website: http://www.stewartcomponents.com/index.html
"Tech Tip #3 - Thermostats & Restrictors
Thermostats & Restrictors
We strongly recommend NEVER using a restrictor: they decrease coolant flow and ultimately inhibit cooling.
For applications requiring a thermostat to keep the engine at operating temperature, we recommend using a Stewart/Robertshaw high flow thermostat. This thermostat does not restrict flow when open. The Stewart/ Robertshaw thermostat enhances the performance of the cooling system, using any style of water pump. However, the Stewart Stage 1 high-flow water pump may require this thermostat to operate properly, and Stewart Stage 2, 3, and 4 water pumps simply will NOT operate with a regular thermostat because these pumps have no internal bypasses.
Stewart further modifies its thermostat by machining three 3/16" bypass holes directly in the poppet valve, which allows some coolant to bypass the thermostat even when closed. This modification does result in the engine taking slightly longer to reach operating temperature in cold weather, but it allows the thermostat to function properly when using a high flow water pump at high engine RPM.
A common misconception is that if coolant flows too quickly through the system, that it will not have time to cool properly. However the cooling system is a closed loop, so if you are keeping the coolant in the radiator longer to allow it to cool, you are also allowing it to stay in the engine longer, which increases coolant temperatures. Coolant in the engine will actually boil away from critical heat areas within the cooling system if not forced through the cooling system at a sufficiently high velocity. This situation is a common cause of so-called "hot spots", which can lead to failures.
Years ago, cars used low pressure radiator caps with upright-style radiators. At high RPM, the water pump pressure would overcome the radiator cap's rating and force coolant out, resulting in an overheated engine. Many enthusiasts mistakenly believed that these situations were caused because the coolant was flowing through the radiator so quickly, that it did not have time to cool. Using restrictors or slowing water pump speed prevented the coolant from being forced out, and allowed the engine to run cooler. However, cars built in the past thirty years have used cross flow radiators that position the radiator cap on the low pressure (suction) side of the system. This type of system does not subject the radiator cap to pressure from the water pump, so it benefits from maximizing coolant flow, not restricting it."
I'm using one of their pumps and have done this mod to my thermostat. With a 190* stat seldom does the195* fan setting ever turn it on unless the car has idled for quite a while.
|01-03-2011 05:56 AM|
A lot of vehicles shut the heater flow off when not actually wnating heat.
Prety sure all AC cars do this.
If there is no valve hooked up the the heater core to shut off the water flow, a bypass should not be needed.
Not having a bypass can create some strange temp patterns util the car fully warms up-----even if there are a couple of holes drilled into the t-stat.
|01-03-2011 12:25 AM|
|kc8oye||if you have a heater core hooked up, will the holes really help? since the heater core acts as a bypass around the t-stat anyway?|
|01-02-2011 08:08 PM|
|This thread has more than 15 replies. Click here to review the whole thread.|