Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Holly carb
User Name
Password
lost password?   |   register now

Thread: Holly carb Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-11-2011 07:52 PM
farm truck
Quote:
Originally Posted by cobalt327
I have no experience w/many of the Avenger carbs, the ones I have dealt with have turned out to be good carbs, but they came to me because they needed attention in the first place. The problems weren't related to the carb design or quality, though.

Until recently I might not have said this- but I would say to take a good look at the BG carb lineup. Their customer service (at least what I have seen here on this board) is second to none.

What is it you're working on?
Working on a 383 strocker - Big Mutha Comp cam , Turbo 350 Trans with a 3000 stall conv. cast heads with 2.02/1.5 vavles 74 cc, weiand intake 10.1 cr
01-11-2011 07:17 PM
cobalt327
Quote:
Originally Posted by farm truck
Thank you for your input. Well back to the drawing board... What carb would be a good on to run ? The guys at the mechain shop said a holley street anverger any input?
I have no experience w/many of the Avenger carbs, the ones I have dealt with have turned out to be good carbs, but they came to me because they needed attention in the first place. The problems weren't related to the carb design or quality, though.

Until recently I might not have said this- but I would say to take a good look at the BG carb lineup. Their customer service (at least what I have seen here on this board) is second to none.

What is it you're working on?
01-11-2011 06:14 PM
farm truck
Quote:
Originally Posted by cobalt327
The 50004-1 is a Holley 4180 carb. One version of the 4180 was used on Mustangs in '83-'85 or thereabouts. They were calibrated for emissions compliance. The primary metering block different, they made adjusting the idle air/fuel difficult if not impossible w/o going into some amount of work because the doggone mixture adjustment was moved to the carb base and covered to prevent "tampering".

The secondary side wasn't so bad. It could be swapped out for an 1850 type metering block fairly easily.

The carb flowed 600CFM, IIRC and had annular boosters, which is a good thing for responsiveness. The fuel bowls (often found w/ugly vapor vents and hoses) can be swapped out for the center hung bowls.

But generally speaking, these carbs are not in demand. To put it mildly.
Thank you for your input. Well back to the drawing board... What carb would be a good on to run ? The guys at the mechain shop said a holley street anverger any input?
01-10-2011 12:15 AM
cobalt327 The 50004-1 is a Holley 4180 carb. One version of the 4180 was used on Mustangs in '83-'85 or thereabouts. They were calibrated for emissions compliance. The primary metering block different, they made adjusting the idle air/fuel difficult if not impossible w/o going into some amount of work because the doggone mixture adjustment was moved to the carb base and covered to prevent "tampering".

The secondary side wasn't so bad. It could be swapped out for an 1850 type metering block fairly easily.

The carb flowed 600CFM, IIRC and had annular boosters, which is a good thing for responsiveness. The fuel bowls (often found w/ugly vapor vents and hoses) can be swapped out for the center hung bowls.

But generally speaking, these carbs are not in demand. To put it mildly.
01-09-2011 11:26 PM
ericnova72 List 6210-3 is a 650cfm spreadbore double pumper, performance replacement carb for direct fit on spreadbore (Q-jet, ThermoQuad) manifolds.
01-09-2011 03:28 PM
bowtieguyss Did you google the part number? You can find quite a bit of information on the net.
01-09-2011 02:47 PM
farm truck
Holly carb

i cant seem to find any info on these list holly 50004-1 and list 6210-3 .. if anyone dont mind the help .. Thank you

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.