Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 4L60e low-reverse clutch retaining clip stuck!
User Name
Password
lost password?   |   register now

Thread: 4L60e low-reverse clutch retaining clip stuck! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-25-2011 11:39 AM
tnsmith10 you are very welcome. glad i could help
01-25-2011 11:00 AM
old yukon Done! Ahha, its the outer snap ring your were refering to.

I just put the rear shaft back in and it all came out, no need to even use a hammer.

Thanks tnsmith 10 for the advice. ( thumbs up!)
01-25-2011 06:21 AM
old yukon tnsmith 10 you said " as long as the snap ring has been removed" was that the large outer snap ring or the smaller inner snap ring (see image)
01-25-2011 06:12 AM
old yukon thanks tnsmith 10
i will give it go.

You said: "that is called the reverse anti-rattle spring" not "lo-reverse clutch retaining clip " thanks for correcting me here.
There are so many different name for it out their. even ATSG call it something different, (see attachment)

Even the directions from the ATSG manual for disassembly seem open to interpretation. eg."remove the lower reverse roller clutch assembly from the case".... which direction?)

thanks again tnsmith 10 .
01-25-2011 05:43 AM
tnsmith10
Quote:
Originally Posted by old yukon
Stuck!

the lo-reverse clutch retaining clip is stuck hard, I had even tried multigrips half a dozen times, no success.
How do i get this clip out of my 4L60e?
Here some picture, not in this order,(clip thumbnail images for expolded view):
-a picture of the location of the clip, and zoomed
- a picture of my attempt,
- a picture of the clip and were I am grabbing it from & the direction of pull,
- and a proposed design modification of adding two holes to the clip IF YOU GM PART MANUFACTURES ARE READING THIS !!! to make our life easier.

I think it has been shoved into the wrong location ??

If anyone has a solution they could post, I would greatly appreciate it.

thanks in advance.
that is called the reverse anti-rattle spring.
its going to be stuck, you gota use the output shaft to knock the center support out and that will free it up. lay the trans down on its back and take a heavy soft blow hammer to the output shaft and hit the output shaft from the bottom of the case. as long as the snap ring has been removed, and the inner lugs of the case arent messed up, it should come right out. you will never get the anti-rattle spring out without removing the center support, without ruining the spring.
01-25-2011 03:05 AM
old yukon
4L60e low-reverse clutch retaining clip stuck!

Stuck!

the lo-reverse clutch retaining clip is stuck hard, I had even tried multigrips half a dozen times, no success.
How do i get this clip out of my 4L60e?
Here some picture, not in this order,(clip thumbnail images for expolded view):
-a picture of the location of the clip, and zoomed
- a picture of my attempt,
- a picture of the clip and were I am grabbing it from & the direction of pull,
- and a proposed design modification of adding two holes to the clip IF YOU GM PART MANUFACTURES ARE READING THIS !!! to make our life easier.

I think it has been shoved into the wrong location ??

If anyone has a solution they could post, I would greatly appreciate it.

thanks in advance.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:54 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.