Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> newly painted frame on jack stands
User Name
Password
lost password?   |   register now

Thread: newly painted frame on jack stands Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-28-2002 01:10 PM
Maverick Golf club covers!! Now there's a thinker! LOL. Thats a good idea! I went for the folded towel method. <img src="graemlins/mwink.gif" border="0" alt="[mwink]" />
08-28-2002 01:07 PM
Kevin45 Golf club covers.

Kevin
08-27-2002 12:15 PM
2oldster Several layers of cardboard topped with a little wax paper will work fine, but make sure it can't slip around.
08-20-2002 11:57 AM
Maverick Thanks guys!! Its already painted. I used Zero Rust and thier clear coat. It looks great. I know powder coating is stronger then paint but it still dose chip. I seen it several times even on powder coating from the factory. and the only way to repair it is to re-powder coat the whole thing <img src="graemlins/nono.gif" border="0" alt="[nono]" /> If this was going to be a show truck then for sure I would powder coat! At least with paint you can just re-paint the place thats chipped. The ZR and clear coat is really strong. I just know sitting on the stands and moving around will cause some damage.

HK Ill see if I can find those boots that sounds like a good idea!!!

Thanks Guys!!
08-20-2002 11:49 AM
Halloweenking Mav, if you go to your local home depot or lows they sell bright yellow soft rubber boots for the top of the jack stands, I beleive they are under $30 for a set. Or you could just go to wally world and get a cheap bag of shop towels and use those, or some of that foam pipe insulation works pretty good.

I'm with willy's if I have the money and want the finish product to last I'm all for powder coating. It will never chip rarely scratch and is vertually fade resistant and needs almost no maintance. Just spray the chunks of grime off whipe it down and go

HK
08-20-2002 09:47 AM
willys36@aol.com I am going to have my '53 puckup frame powder coated. Got tired of chipped paint. Can you put a couple of 1"x4" boards wrapped in towels or such across the tops of the stands and under the frame while you are hooking up the suspension? Bunji-cord the frame to the boards.
08-20-2002 07:52 AM
Maverick
newly painted frame on jack stands

I just finished painting the frame on my '49 Chevy truck. I built what I call a frame rotisserie to paint it on. Its like two large engine stands on each end of the frame, I can roll the frame all the way over. Anyway! now that its painted I need to get on the ground on the jack stands. Any one have any good tricks on protecting the new paing from the jack stands?? I thought about spraying that rubberized under coating on the top of the stands. Or some thick towles. Any other bright ideas?? <img src="graemlins/pimp.gif" border="0" alt="[pimp]" /> Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.