Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> engine
User Name
Password
lost password?   |   register now

Thread: engine Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-16-2002 03:02 AM
roys63 A Motorcraft 2 barrel carb from a 78-80 302 PU will bolt right up on this and is a very simple carb to work on and you can pull all that vac crap off and plug, This carb is about $80 to 100.00 rebuilt from Advance parts stores, I have changed out may of these, this will run better than new.Be sure cad converter is ok! not pluged.
02-15-2002 08:38 PM
shootdown thanks Tom . ask a friend of mine who's into race cars open wheel six's and such. anyway next day he shows up with a box of ford carbs. older ones , still have the same valve but vaccum is different so it wont blow the diaphram. planto get up early in the mornin find the hammer,circular saw and some cold chisels change one or both see which one is the best. can be any worse. next step will be the engine swap then I'd have a chefrd. heavens my life just flashed before my eyes

Thanks Tom
P.S. thanks everyone,the help here is first class. still voting for rods built by owners. Roy great site!!!!!!!!!!
02-14-2002 05:42 AM
57Chevyman If you are going to swap the motor you should not need a new rearend. If I am not mistaken the rear in those is the same a s the FOX mustang. Should hold up fine for streat duty with under 500 HP.
02-13-2002 06:40 PM
Tom if I'm not mistaken the standard motorcraft duce will fit if you get an EGR plate to go with it, we have done it on 302s
02-13-2002 06:39 PM
Tom if I'm not mistaken the standard motorcraft duce will fit if you get an EGR plate to go with it, we have done it on 302s

[ February 13, 2002: Message edited by: Tom ]</p>
02-13-2002 05:45 PM
shootdown THANKS guys, one of those things where a person needs some independent input. will check on a holly. the shades on the smilie face are cutting goggles for the engine swap you mentioned ,put in a sbc. then all I'd have to worry about is fords better idea body.
I realise this is a hot rod site BUT , if I'v got to change the carb meby I'll just do the engine swap , drop the spindles a couple of inches slip in a 10 bolt posi tub the bed cuz I'll need some good meats for traction. then my question will have been leagit cuz it would be a rod!

THANKS again
02-13-2002 08:28 AM
1meancuda If I remember right, someone out there makes a swap kit to put a V8 into Rangers and S10's. I'd go with one of those!!!
02-13-2002 05:59 AM
LS6454 Go ahead and get the Holly, you will be glad. My
grandfather was a big time Ford man and the first
thing he always did was change the carb.
02-13-2002 05:36 AM
57Chevyman Shoot down,

Is the carb you are talking about the Veriable Venturi. I hate them too! My dad and I rebuilt one once and it was junk regardless of what you did to it I finaly adapted an earlier model to replace it. Holley makes a direct bolt up to replace it. If it is the VV S&*#t Can it and put on the Holley. You will not belive it is the same vehicle.
02-12-2002 09:11 PM
Roy Newton- exprotech Yes I have a Idea get ahold of Nascar and because its a ford they will let you change the rules. Then you could use a dodge part. Nascar could even make the rules so the big brown truck could win. I think holley makes a replacement for that hunk of Iron. ROY
02-12-2002 05:33 PM
shootdown
engine

just spent 15 minuates composing a new topic click add my computor crashed ,hate computors. speaking of HATE I HATE motocraft carbs!

have an 84 ranger 2 wheel drive 2.8 v6 . one of fords better ideas for carbs need to replace this motocraft with anything ! a person with a 5 gallion bucket would be better than this piece of pot metal ANY IDEA"S

thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.