Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> 472 big block cadi
User Name
Password
lost password?   |   register now

Thread: 472 big block cadi Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-05-2011 07:30 AM
327NUT Everything said above is true, very high nickle block and they perform well when hot rodded. The stock rods are cast and should be replaced with affordable aftermarket forged pieces if you want to run it up to 5500 often.
I'm in the process of building a '75 508" engine for my '32 Victoria, wanted something different, learning as I go. You can look at 2 websites....www.500cid.com (Maximum Torque Specialties) and www.500cadparts.com. They both carry parts to really wake up the 472/500 Cadillac.
02-05-2011 07:11 AM
timothale
Caddy torque

I bought a caddy for $25, it had messed up wiring, I put the 472 engine and trans into my sawmill, Lots of low end torque, I run it at 2200 rpm in reverse direct via u joints to the 4 ft round blade, The caddy has high nickle content blocks, they last forever,
02-05-2011 04:54 AM
American Muscle Sound like its worth getting then. although i have nothing to put it in. lol
02-05-2011 04:52 AM
1957plymouthhemi First thing on a deal like this is to verify what the guy selling it says is actually what it is. Verify the casting numbers to make sure it is in fact a 472/500 and not a 425 or 368. The valve covers do not look right for a mid 70s 472. The sellers comments about being a big block and that it was too big to fit in an 83 Monte kind of tells me the seller doesn’t know what he’s talking about (should be more along the lines of “I got in over my head”).

Comments like “ran when pulled from truck” always make me a little cautious (especially when Cadillac engines were not installed in trucks)...... how did it run and how long has it been sitting out in the elements.

I notice it is missing most of the accessories/brackets which can be a PIA to find and depending on the oil pan you may need to dig up a El Dorado pan or aftermarket one ($$$$). At a minimum you will want to pull the timing cover and replace the timing chain and put in new valve seals.

Depending on the year and compression a mid 70s 472 should make close to 500 foot pounds of torque around 2500 RPM and stock valve springs float at around 4200 RPM. Geared properly (highway gears in the 2.75-3.25 range) work very wells with these engines. Properly set up in say a G Body it's not too hard to get a fairly stock 472/500 into the 12-11s and still be very streetable.

If the engine needs rebuilt you’re looking at around $2000 for a stock rebuild.......start adding speed parts and it gets real expensive real quick.

What are you looking at putting it in? The Caddy engines are long and tall, and while they can be put in a lot of different vehicles it usually is not a “bolt in” deal and will require some amount of skill. The often listed 50 pound difference between the weights of a Small Block Chevy (like the 305/350s) and the 472/500 Caddy is in fact closer to 100-125 pounds. Things like springs and cooling system capabilities will need to be considered.

If you are planning such a swap be honest with yourself about your abilities to actually make it happen.
02-05-2011 04:05 AM
ericnova72
Quote:
Originally Posted by American Muscle
is it known for performance?
Not really, makes big amounts ot torque just because it is soo large. The 472 and especially the 500 are somewhat used for performance, there are a couple of companies that specialize in performance parts for these. A bit more expensive than a BBChevy, lighter than a BBChevy, almost SBC weight. BBC headers nearly fit, cutting off the BBChevy flanges and slightly tweaking the tubes allows Cadillac flanges to be welded on.

It is a slightly popular swap into chevy trucks, good towing power and usually better mileage than a BBChevy. There are a few people who use them in Hotrods. Will basically fit anywhere a BBChevy, BBOlds, Pontiac, BBBuick will fit if you want to do the swap work.
02-05-2011 02:57 AM
American Muscle is it known for performance?
02-05-2011 02:10 AM
ericnova72 Don't know why he calls it a big block, there is no small block Cadillac. Typical of a non-gearhead, "its big so it must be a Big Block". It is just a common 472 Caddy engine, same lineage as the 425 and 500 are. Nothing rare or odd about it.
02-05-2011 12:38 AM
American Muscle
472 big block cadi

check out this ad from criagslist. Anybody have any knowledge of this monster.




http://littlerock.craigslist.org/pts/2197926184.html

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.