Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Power seats hook-up
User Name
Password
lost password?   |   register now

Thread: Power seats hook-up Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-22-2011 07:37 PM
39chevy Thanks again!
02-22-2011 07:27 PM
crdnblu NO reason to go with any larger gauge than existing, when you splice/extend your wiring to get to your console. Just make sure that your all connections are solid, & again, I recommend using split-loom, or equivalent, to protect the wiring. (nag, nag, nag.....)
02-22-2011 05:03 PM
39chevy
Seats

One last que: I have got a complete switch box for both seats, (Console) I am going to make my own wiring harness to make this thing work, my que: is I know 10 guage is good for power seats, but my wires coming out of my control panel are really small guage(Circuit board) It won't be a problem splicing to them, but will that be o.k. to do it that way? Thanks again, Dana
02-19-2011 08:55 AM
39chevy Thanks again!
02-19-2011 08:45 AM
crdnblu
Bucket Seats Wiring Harness?

I made mine. Reason? That's pretty much what the factory did.....When I pulled my seats out of the donor Eldorado, the factory STOCK main wiring leads from the two bucket seats (12V, & Ground) were soldered together, then shrink-wrapped, leading into a factory connector, then to the circuit breaker/fuse box.

For our street rod application(s) 10 gauge 12V, & ground wiring is the size to use for the offered 30 amp load. Either use the proper sized butt-connectors, or solder the connections if you prefer, but make sure to SHRINK-WRAP the connections, regardless. For further protection, I would also split-loom the entire harness, as the seats are one of the biggest amp draws in any vehicle.

My seat wiring goes to one of these, or you could use something comparable (pic):

http://www.ronfrancis.com/prodinfo.asp?number=PB-15
02-15-2011 06:01 PM
39chevy Both seats seem to fine, WHERE would I find a wiring Harness just to attach both buckets together? Thanks
02-11-2011 05:10 PM
39chevy Thanks 4 all the help, I should be good to go, I did purchase the control swith, thanks again!
02-11-2011 08:52 AM
crdnblu
Cadillac Heat & Lumbar Module

Here's a link to one for sale, if needed:

http://cgi.ebay.com/ebaymotors/92-96...item19c2816361
02-11-2011 08:04 AM
crdnblu
Info Update

39 Chevy.......Some added info/corrections:

-The 12V power connection is indeed 30 Amp, not the lower rating that I had given B/4. All diagrams that I have show a 30 amp circuit breaker supporting BOTH seats, combined.
-Attached is a PDF file wiring diagram for a '97 Eldorado. I believe that you'll find (as I did), that very few changes have occurred through the years, following yours. If your seats have heat, & lumbar support built-in, you'll need the Cadillac console mounted control module, & wiring harness, too, as these controls were NOT mounted on the seats in the early to mid 90's. (Attachment [A red 12V is shown; same as your orange 12V wire.]
02-10-2011 12:42 PM
DanielC This is my battery. Notice the fuse between the two 6 volt batteries.
(This is also a test of getting a picture in here.)


The wire harness on the battery is for testing boat trailer lights.

I also recently used the battery to run the electric window regulator for my for Aerostar to a position that would make it easier to slip into the door.
02-10-2011 11:54 AM
EOD Guy If you need a small 12v sealed battery by all means purchase one, otherwise a charger will provide a good strong 12 source with low amps, why are low amps important? if you cross the wrong set of wires ie..... short them out, you won't fry the motor!
02-10-2011 11:24 AM
DanielC I use a sealed Gel cell 12 volt battery for bench tests. It is a battery that came out of a UPS supply for computers. These batteries are also very common in emergency power out lighting in factories, schools, and many other public buildings.
02-10-2011 08:47 AM
crdnblu
Cadillac Power Seats

OK, here's some info for you, based on my research into my 90's Cadillac Eldorado buckets:

"blk has 2 wires, blk and orange w/blk stripe": Blk is ground; orange w/blk stripe is 12V constant power, typically fused @ 20-25 amps.

"blue plug has 4 wires, pink w/blk stripe, green w/white stripe, blue w/white stripe, white w/blk stripe": This connector goes to the Cadillac seat control switch assembly (pic). From my experience, it will be VERY difficult to operate the seat without the Cadillac button assembly, as it contains a basic printed circuit board to cause multiple on/off actions when each button is moved. I found my switches on E-Bay.
I would also suggest buying a small sealed scooter, or motorcycle battery, for bench testing 12V electrical components; they give more consistent voltage than a battery charger. Attach some made-up 12 gauge test leads, with covered/protected alligator clips, & you can test any NEW circuit, anywhere on your ride.
02-07-2011 05:54 PM
vicrod See attached schematics of power seats.

vicrod
02-07-2011 04:34 PM
EOD Guy 12v battery chargers work great for a pwr supply when doing bench tests
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:24 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.