Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 6 pad torque converter
User Name
lost password?   |   register now

Thread: 6 pad torque converter Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-18-2011 05:59 AM
carlk4728 Thanks everyone for the advice. I went with lovin's suggestion and just bolted it up with three bolts.

Maybe I'll find a powerplant that will justify the use of the dormant three pads down the road. So I guess, in hindsight, I'm glad I accidentally bought the 6 less thing to upgrade in the future!
02-14-2011 02:00 PM
Converter bolt spacing

GM flex plates often have dual bolt spacing (6 bolt holes) to fit a torque converter with either a 11.50" and 10.75" bolt pad spacing. The TH350 and TH400 torque converters come with 3 bolt pads but may have either bolt spacings. If your flex plate only has 3 bolt holes and they don't fit the bolt spacing on your new torque converter, you will have to purchase a flexplate that has a dual bolt circle.

I went through this puzzle with my '91 S10 Blazer 4.3L V6 engine when I had the engine built with 350 Chevy forged pistons and internally balanced. The 4L60 (700-R4) transmission in my S10 Blazer use counter-weighted flex plates for externally balanced engines. When I had the engine built and internally balanced, I had to use a heavy duty (0.125" thick) 168 tooth flex-plate, 3" flange bolt circle for the one-piec e seal without a counter weight and was zero blanced.

My engine builder knew exactly which HD flex plate to use. He provided an ATI #915534 non-counter weighted dual pattern flex-plate to use with a torque converter that has either a 10.75" and a 11.50" bolt circle, 168 tooth starter gear, a 3" crank flange bolt circle and zero blanced.
02-14-2011 11:02 AM
75chev4x4 Had the same thing when I went from big block to small block, 454 used six bolts and the 350 only used 3, called the tranny shop and they said three is fine for the 350.
02-13-2011 02:37 PM
6 Pad Converter

Dont Redrill Anything! Just Put The Three Bolts In It,u Wont Have Any Problems,and Yes The 6 Pad Is Just For High Output Torque
02-13-2011 01:39 PM
junior stocker Redrill the plate for the additional 3 holes. The six bolt converters were usually for bigger trucks/motor homes/diesel rigs. I don't think I'd just not not bolt them on, they may create a vibration/noise issue, and you'll be back under there again correcting it. Would they possibly exchange converters for you? You could also buy another flexplate already drilled for the six bolt converter.
02-13-2011 10:50 AM
6 pad torque converter

When I ordered the torque converter for my rebuilt th400, I was asked if I wanted a 3 or 6 pad version. So I peaked under my truck at the flexplate, saw 6 mounting holes, and based on that info I ordered the 6 pad. I guess I was wrong, though, because now that it's all mounted (yes, without verifying fitment) I see that three of the six mounting locations on the flexplate don't line up with the TC (they create a pattern that is of a smaller diameter than the six on the TC). I assume that this is to provide compatibility for two different kinds of three pad TC's (a small and large bolt pattern diameter).

So now to the meat of the issue: can I safely bolt this 6 pad torque converter to my flexplate using just three bolts?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:12 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.