Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> please help id this 10 bolt posi
User Name
Password
lost password?   |   register now

Thread: please help id this 10 bolt posi Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-11-2011 12:36 PM
cutthroatkid I found the code,went&really hit it hard with a wire brush&anyhow looks like 4yp g4142 I can't seem to find any info on it.Any ideas?
03-11-2011 03:06 AM
ericnova72 Just having both axles turning in the same direction does not gaurantee a posi, a burnt up open differential that has friction welded the spider gears to the pin will behave the same way. Best to remove the cover and see exactly what you have.

Widtn measurement needs to be from where the wheel bolts on to get the true width. Nobody lists them by backside of the drum measurements.
03-11-2011 02:35 AM
cobalt327
Quote:
Originally Posted by cutthroatkid
This is the date code. It says the casting was made in a year ending in "4". The stamped axle tube numbers are what's really needed.
03-11-2011 12:55 AM
cutthroatkid Ok I can get some more pix in the morning.I know its a posi,I sat it up on aome blocks&both trums spin the same way.How should I measure it?I just dis from inner hib to hub it was 58 inches.It looks pretty much identical to my monte carlo rear.I took some degreasser&wd40&a wire brush to it&can't find anymore codes Thanks for the help.
03-11-2011 12:38 AM
ericnova72 It is definately an 8.5" 10-bolt, identified by the cast corner "blocks" at 5 o'clock and 7 o'clock just below the cover face. I don't see a posi tag(it would have been an stamped aluminum tag about 1-1/2" long x 5/8" wide saying "use positraction differential lube only", attached to a cover bolt, but they frequently corrode and rot off) so you'll have to remove the cover to know for sure what is inside.

Width measurement needed is wheel mounting surface to wheel mounting surface. Just off hand based off the width you have given and the suspension brackets is that it is 73-77 A-body, but that is just a guess at this point.

A picture of the end of the housing where it meets the brake backing plate would help, as a look at the bolt pattern and size could narrow ID down further. There is the possibility it is a Type O(Oldsmobile) 8.5" and the housing end is different.

Could also be an 8.5" from a full size GM(Caprice/Impala) depending on total width.

The #'s you have posted won't help.
03-11-2011 12:05 AM
cutthroatkid
03-10-2011 11:34 PM
cutthroatkid Ok it'll take me a bit to get all of these piz uploaded can't find any other codes me& 2 othee guys looked. Also if it helps from the back of the drums one to another meaure about 58 inches.
03-10-2011 11:22 PM
cutthroatkid Let me see if this works.
03-10-2011 10:24 PM
ericnova72 Only code that will mean anything will be stamped into the forward side of an axle tube. Casting #'s won't ID it. a picture would make this real easy.

There is an ID chart at www.novaresource.com for ID'ing the different 10-bolts. Click on "site map", then on "axle codes" and it will take you to the ID page.
03-10-2011 10:13 PM
cutthroatkid
please help id this 10 bolt posi

I have a rear end that was in my grandfather's shop after he passed.Its a 10 bolt looks to be an 8.5 &it is a posi.The only codes I can find are one that says gm 49 another that says 12515002 &one more that has what looks like a o with a horizontal line in it thene 154 and another o with the horizontal line like oe 154 o. PLEASE help Ive looked&looked&can't seem to find no info.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.