Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Three-Wire Delco 10SI/12SI Alternator Question
User Name
Password
lost password?   |   register now

Thread: Three-Wire Delco 10SI/12SI Alternator Question Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-01-2012 01:42 PM
Augusto why would be practical to have only one wire to the alternator?

if for looks, the 3 wires can go inside a nice loom and would make no difference,

I have used one wire alternators and they need to be revved up to start charging, I don't like that much.

so why going one wire if 3 is fine?
03-16-2011 07:31 AM
joe_padavano
Quote:
Originally Posted by T-bucket23
The main difference between a 1 wire and a 3 wire is the regulator. I have read that some of the 1 wire regulators will work exactly like a 3 wire if you connect all three wires and some wont. Depends on the manufacturer. Maybe this is why there is no clear cut information.
That is what I've seen as well. If you look at the two tabs for the connector that stick through the alternator housing, some one-wire units actually have these two tabs connected by a little metal bridge strap. Obviously, this won't work as a three wire unit. I have never seen an OEM one-wire unit, though some marine applications may be set up that way.
03-15-2011 08:13 PM
75gmck25 I don't think Delco ever made an OEM alternator that was designed for 1 wire operation. If you have a real OEM Delco 10si or 12si alternator, or equivalent, it should always be a 3 wire. However, if you have a Delco that was converted to 1 wire it would have a self energizing regulator.

These links explain what regulator is used in a 1 wire alternator.

http://www.purplesagetradingpost.com...o/onewire.html
http://search.waiglobal.com/partnum.aspx?part=D10SE12

Bruce
03-15-2011 04:04 PM
T-bucket23 The main difference between a 1 wire and a 3 wire is the regulator. I have read that some of the 1 wire regulators will work exactly like a 3 wire if you connect all three wires and some wont. Depends on the manufacturer. Maybe this is why there is no clear cut information.
03-15-2011 03:36 PM
hduff
Three-Wire Delco 10SI/12SI Alternator Question

There's a lot of information out there about the three-wire versus one-wire alternator setup, and I'll just share this:

One-Wire versus Three-Wire
http://www.madelectrical.com/electri...hreewire.shtml

Explanation of how the idiot light circut is wired and how it works.
http://www.hotrodders.com/forum/gm-3...up-154278.html

Explanation of how the voltage sensing circut is wired and how it works.
http://www.madelectrical.com/electri...esensing.shtml

And a picture of the wiring using a 1N5408 diode and NOT using the voltage sensing circut.



While the picture suggests a 10-guage wire from the alternator stud, my perference is to use 8-guage wire. And rather than pig-tail the voltage sensing line to the stud, I run a wire to the feed stud of the fuse panel so I can atually get some value from voltage sensing.

Anyway, enough sharing. My question is this:

In all I 've read it's not been clear whether any Delco 10SI/12SI can be used in three-wire mode just by connecting all three wires or if only some of the built-in regulators are capable of doing it.

What's the answer?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:30 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.