Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Need advise on Ford 300 engine swap to a Ford 400
User Name
Password
lost password?   |   register now

Thread: Need advise on Ford 300 engine swap to a Ford 400 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-22-2011 03:59 PM
aztek_warrior Thanks for all your input, After all the serching around, I was also leaning more towards just a rebuild on my 300, My daily drivers also has one and its been more than a great engine, will more than likely be rebuilding....thanks everyone..
03-21-2011 01:06 AM
DanielC The 300 inline six is a good truck engine. It has a lot of torque, and to get the same bore and stroke in a V8, you would have a 410 engine. (390 FE, with a 428 Crankshaft)
That engine makes a good engine for a Ford Truck, but you do not have one.

It was pointed out to swap a 400m V8, it would be easiest to have a donor truck.

If it was my truck, I would rebuild the 300. More than enough power, and potential for reasonable gas mileage.
03-20-2011 10:16 PM
66GMC Not disagreeing at all, Willowbilly ... as I am somewhat of al old "Ford Man" as well. (Ford partsman for 14 years, starting in 1979)

As I said earlier ... the 351M/400 was, IMO, a temporary powerplant stuffed into pickup trucks starting in 1977, discontinued in 1982. These engines fell victim to EPA regulations. Compliancy required, IIRC, retarding the valve timing 2. Horsepower and fuel economy both fell off as a result.

As you said, they also had "engine management issues" which included overheating and detonation problems. The "fix" was a re-curved distributor that was issued on a "Campain" near the end of the life-cycle ... 1981-82.
03-20-2011 09:59 PM
willowbilly3
Quote:
Originally Posted by 66GMC
351M / 400 engines got a bad rap. They were introduced to replace the aging FE series during an emissions transition phase ... so the engineers were scrambling to come up with a suitable powerplant for the light trucks.

The 300 6 was a fairly dependable and even torquey little engine ... but a 6 is still a 6, right?

The 429 or 460 (385 series) is another possibilty ... one with a lot of hot-rod potential.
As a Ford man, the 351M/400 is my least favorite engine because I had them in my shop back in the day and they had really crappy engine management systems. I have seen 400s built to run but to me it's not worth the hassle, and they were mostly gas hogs too. I like my 300 but it isn't the end all of engines. first off there is nothing like the sound of a V8, sorry six banger guys, they just sound like puke for the most part.
I like the advice of going to a 351W, bell housing, clutch and all will still work (not the flywheel even though it will bolt on). Also remember that mixing and matching Ford bits can be (and usually is) an exercise in futility at some point unless you have a complete donor vehicle, or two.
Also on edit, you will need different engine towers to swap. The 300 ones work for the FE engines by just moving them back. Small block use their own and the 351M/400 use their own.
03-20-2011 09:51 PM
66GMC 351M / 400 engines got a bad rap. They were introduced to replace the aging FE series during an emissions transition phase ... so the engineers were scrambling to come up with a suitable powerplant for the light trucks.

The 300 6 was a fairly dependable and even torquey little engine ... but a 6 is still a 6, right?

The 429 or 460 (385 series) is another possibilty ... one with a lot of hot-rod potential.
03-20-2011 09:41 PM
327NUT In my humble opinion a 400 is a boat anchor....free or not, not worth the trouble of the swap, but it can be done and you would have a V-8! If you want a better V-8 stick a 351W in it or rebuild the 300.
03-20-2011 08:51 PM
aztek_warrior
Need advise on Ford 300 engine swap to a Ford 400

Hi everyone, well here is my dilema. I received a Ford 400 from a friend of mine (free). I would like to use this engine on my pick up, I currently have a Ford 300 with a BW T-18 granny low 4spd trans, the truck is a 76 f100 custom 2wd. I know I need the bellhousing, flywheel, starter, alternator, distributor, water pump, gaskets need to be changed on the 400 but for the money that i'm looking at for all these items seems like I could just might as well rebuild my 300...Need some advise on if this swap would be worth the time and money spent..This truck is used only to cruise around, I don't tow or haul anything with it, but it would be nice to have a V8 in it . What advise could you guys offer me?? I would greatly appreciate your input on the matter..getting a little frustrated.

P.S. and i thought the most difficult decision in life was to get married or not...LOL
thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.