Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> from 4 door sedan to 2 door coupe.. torch time..!!!
User Name
Password
lost password?   |   register now

Thread: from 4 door sedan to 2 door coupe.. torch time..!!! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-22-2011 08:49 AM
Augusto indeed my idea is going coupe, the trunk lid is longer but I plan on just using the same unit but placed a little more inclined, the roof line is quite different but since it will get a chop job there's lots of fabrication time ahead.

about glass, yes I tought of leaving it fixed, the a/c will cover that up nice, the front glass will roll down but I'll make it a one piece window, deleting the little swing out vents, I've done this before.

I'm watching at your pics, they are very cool.
03-22-2011 06:05 AM
redsdad If you are talking 2 door sedan, then yes. Lengthen the doors. buy EMS quarter repairs and move the B-pillar.

2 door coupe is a different animal. Trunk lid is different. Trunk hinges on the outside rather than inside. Slanted B-pillar. Different roof line.

My project journal has some good photos of what needs to be done to the floor and quarter area in front of the rear fender. If I were you, I would probably forgo roll up quarter glass. Glue the glass in. If I had it to do over again and knew how much time everything was going to take, I would have probably glued mine in and I had a set of window boxes to start with.
03-21-2011 07:31 PM
Augusto you bet, I'll do a photo album of my progress, I won't start soon because I'm working in the engine of my elcamino rigth now, but I can't wait to start doing my '46, the frame is ready though, it's a camaro front clip welded to a malibu frame with the front end removed and the length adjusted to give the propper wheelbase, 454 engine, the rest of the drivetrain is not decided yet but will be automatic for sure, hopefully by mid april sparks will be flying.
03-21-2011 06:29 PM
eloc431962 [QUOTE=Augusto]I considered going topless but after some fiddling with photoshop I didn't like it much, I found the fat fenders 2 door idea the best for me.[/QUOTE




Whatever you decide Augusto , I hope we can watch.



Cole
03-21-2011 06:01 PM
Augusto I considered going topless but after some fiddling with photoshop I didn't like it much, I found the fat fenders 2 door idea the best for me.
03-21-2011 05:19 PM
TucsonJay I have been looking for a '49-'50 Merc body in this area, for a relative. Once he realized there just aren't any cheap unbuilt Merc 2-doors, we started exploring what could be done with a 4-door

Besides the obvious 2-door conversion, we discussed a 4-door convertible, with carson top and suicide rear doors like the mid sixties Lincolns... a "Ranchero" version... a panel... a roadster pickup... or a flatbed.

If it's custom, you don't have to limit yourself to the factory styles only.
03-21-2011 05:10 PM
Augusto
Quote:
Originally Posted by kc0kfg
There is a guy over on the Hamb that did this to a 40's ford you may want to take a look at the work involved,

Do you access to a 2 door, doors and roof section ? they would be of great help.
for what I have researched seems like the 2 door models were never imported to this shores, so no luck finding them.
03-21-2011 05:07 PM
Augusto
Quote:
Originally Posted by artsvettes
I have never done a chop job but have done some extensive body work over the years. I would put down the torch idea. To much heat generated from that. A sawzall and angle grinder with cutting discs would be my tools of choice
well actually I said torch just because it sounds cool, I will use my plasma cutter and the tools you mention, the oxy torch is reserved only for 1/2 or thicker cuts. and btw the plasma cutter head is also called torch.

what do you think of the idea?
03-21-2011 04:06 PM
kc0kfg There is a guy over on the Hamb that did this to a 40's ford you may want to take a look at the work involved,

Do you access to a 2 door, doors and roof section ? they would be of great help.
03-21-2011 03:55 PM
artsvettes I have never done a chop job but have done some extensive body work over the years. I would put down the torch idea. To much heat generated from that. A sawzall and angle grinder with cutting discs would be my tools of choice
03-21-2011 03:11 PM
Augusto
from 4 door sedan to 2 door coupe.. torch time..!!!

ok the search is over, no more looking around, definitely no 2 door antique cars are left around here anymore, I have this '46 4 door chevy fleetmaster sedan that I decided to convert to a 2 door coupe, done some homework and found that both have the same wheelbase and share most of the parts, the torch will be needed only on the rear quarters, doors, top, trunk, etc. I'm willing to take the challenge, I have no plans or measurments, so for sure will not have the exact measurments but nobody will know that anyway so I don't care, I'm just after the coupe look, and maybe will chop the top a couple of inches while the torch is lit. LOTS of work coming up for shure but that's part of the fun, this is what hotrodding is about anyway, isn't it?

A buddy is pretty interested in doing the same thing to his '64 chevy II, so if I succeed, I'll have plenty of work coming up.

If anyone has done this before will you share your experience? no matter what car you've done, most are about the same.

or if someone by chance happens to have plans or measurements of the 2 door body '46 chevy, you'll be my best friend forever.

cheers, from the middle of the world.

Augusto.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:12 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.