Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> '59 Ford Rack and Pinion
User Name
Password
lost password?   |   register now

Thread: '59 Ford Rack and Pinion Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-22-2003 02:44 PM
kevkoracing These spindles are rear steer. I've seen them used on a '60 convert. using the stock steering. Thanks for the rack info. They use the big brakes and actually are a 1.5" drop from the factory drum set-up.
08-21-2003 09:27 AM
EBlack36 The length of the steering arm is one or the reasons I have not chants the Cougar to a rack yet it would increase the radius by about 5 feet. I have found out that a BMW 5 series is supposed to be closer for the Mustangs and Cougars with rear steer. Going to salvage yard labor day weekent to figure it out unless it is still as hot as it is now.
08-21-2003 07:36 AM
farna Yeah, I missed the 77 part! Steering arms to front, use 80s T-bird rack (or Mustang, or Aerostar van), if steering arms to the rear use an 80s Taurus rack. One thing to note: steering arm length. From center of ball joint to center of tie rod end is only 5" for the R&P. Regualr steering box arms may be as long as 7", which will greatly reduce the turning sicrcle. You may have to cut and weld or bend your arms if they are cast in unison with the spindles. I'm making tubular arms for my car, but the arms bolt off.
08-21-2003 07:31 AM
EBlack36 The spindles you are using, are they front or rear steer? If they are fron steer use a rack from an 80's t-bird.
08-20-2003 07:02 PM
kevkoracing ^^^^
08-17-2003 01:17 AM
kevkoracing I'm sure that we are on a different page. This is a 1977 t-bird that I'm talking about. This car is the one that I'm robbing the spindles and front brakes from. I know this car did'nt have a rack.

I'd like to know which rack I should use for the conversion.

This conversion is still a rear steer deal. I'd like to know what somebody has already used for this application.

All this is going ona '59 Ford with a front sump 351M/400

I'm sure that out there somewhere, somebody has done the same swap.
08-12-2003 08:07 AM
farna If using T-bird spindles, use the T-bird rack. It will mate to the GM column since both use 3/4" double D shafts. You might have to take a GM and Ford shaft, pull them apart at the slip joint, and mate them (I did that). The T-bird rack will use a GM PS pump (or Ford). The rack should mount along the plane between the inner pivots of the lower arms to prevent bump steer, and must mount in front of the crossmember. If you need to mount behind the crossmember reverse your spindles (left to right) and use a Taurus rack.
08-11-2003 02:55 PM
kevkoracing
'59 Ford Rack and Pinion

I'm sure this has been covered somewhere on here, but l'll ask anyway. What is the best set-up to use? I've already got the spindles and brakes taken care of ('77 T-bird). Now I need to know which power rack to use. I'll be using a GM type tilt steering column.

Thanks,
Kevin

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.