Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Which way does the low reverse roller clutch assembly go?
User Name
Password
lost password?   |   register now

Thread: Which way does the low reverse roller clutch assembly go? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-22-2011 05:55 AM
old yukon I had a good teacher !
04-22-2011 05:05 AM
tnsmith10 there ya go. looks like you got it and correctly.
04-21-2011 09:08 PM
old yukon See that was the trick, i had that race lubed up like a slimy squid, and the slight angle also helped.

Here is the final result does it look right?, is the roller clutch the right way?
The race locks up when i turn it to the left(or counter clockwise) and freewheels when i turn the race to the right (or clockwise).

04-21-2011 05:38 PM
tnsmith10
Quote:
Originally Posted by old yukon
Thanks again for the reply tnsmith10.

Ok, I took the inner race out. and it only went in like image B, with the inner tabs facing up.
I then installed the snap rings. Then tried to to put in the inner race, but it would not go in either way.

I can fit the race into the roller clutch assembly, but cant get them both into the retainer, or
I can fit the roller clutch assembly into the retainer, but then can get the race to fit.

Getting all three to fit seems impossible.

I must be doing something wrong here, it cant be that hard.

Waiting for more ideas !
once youve got the roller assembly in the center support. the inner race has to be "rolled" in at a very slight angle. its not easy, especially for the first time, when i was a teen at my dads shop i built 350's ( or engine or cylinder head rebuilding) during summer break from school, and it took me what seemed like forever before i could get the inner race to go in.
i recommend that everything is dry as it will help the race catch the rollers and "roll" in place. ive tried assembly gel or other lubes, and it was just a slimy mess that didnt work for me.
oh and your right, it does go in like in pic B. i should know better than that 1st thing in the morning when im not quite awake yet. from the front side showing in the pic, if you face towards you, the race should turn clockwise.
04-21-2011 11:52 AM
old yukon Thanks again for the reply tnsmith10.

Ok, I took the inner race out. and it only went in like image B, with the inner tabs facing up.
I then installed the snap rings. Then tried to to put in the inner race, but it would not go in either way.

I can fit the race into the roller clutch assembly, but cant get them both into the retainer, or
I can fit the roller clutch assembly into the retainer, but then can get the race to fit.

Getting all three to fit seems impossible.

I must be doing something wrong here, it cant be that hard.

Waiting for more ideas !
04-21-2011 10:15 AM
tnsmith10 you have to take the inner race out to install it. should just drop right down in (only will go in 1 way) and install the snap ring. once you have it in, then you can install the inner race. pic A looks right to me, just gotta take the race out.
04-21-2011 06:32 AM
old yukon
Which way does the low reverse roller clutch assembly go?

I have tried to get this thing to fit, but it wont budge. Its a Borgwarner LOW & REVERSE. ROLLER CLUTCH. (part no. 28571am) for the 4L60e.

ATSG say and shows the following:


I have tried both ways, but neither fits.



Is there a special trick to this, how do you do it?

I would be grateful to anyone willing to help me out here.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.