Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> consew 206 rb-5
User Name
Password
lost password?   |   register now

Thread: consew 206 rb-5 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-27-2011 08:54 AM
DanTwoLakes You're going to lose 2" of belt length with a 1 3/4" pulley, so if you don't have 2" of adjustment, you'll need a 2" shorter belt.
04-27-2011 08:13 AM
rodrieguz
Quote:
Originally Posted by DanTwoLakes
The belt was off the machine? Did you change the motor pulley? If so, you really need to tighten the belt or adjust the motor pulley so that it is in a straight line between it and the machine pulley, 'cuz that should never happen.

I think it may have come off when I tilted the machine. The pulley i have is a 3" If I get the 1 3/4" to slow the machine down would I need a different belt?
04-27-2011 05:09 AM
DanTwoLakes The belt was off the machine? Did you change the motor pulley? If so, you really need to tighten the belt or adjust the motor pulley so that it is in a straight line between it and the machine pulley, 'cuz that should never happen.
04-26-2011 06:29 PM
rodrieguz thanks for all the tips and advice, don't laugh but the belt was off the machine, if that makes any sence. I put it back on and everythig worked ok.
Still trying to get the tentions in sinc.

Thanks again guys
04-26-2011 11:36 AM
DanTwoLakes Is the top thread on the machine correctly threaded? Do you have the bobbin thread installed correctly? The thread pulls off the bobbin to the left side. If you put it in backward the bobbin thread won't get picked up. You also need to get the bobbin thread under the spring steel tension on the side of the bobbin case. Are you threading the needle from left to right? Does the thread go through the thread guide just above the needle at the bottom of the needle bar?
04-26-2011 10:15 AM
rodrieguz just bought the machine, it is fairly new used a couple times by the previous owner. It worked fine before, I sewed two pieces of carpet and was maybe practicing with some scraps and it stopped sewing
04-26-2011 09:37 AM
Coodeville
Quote:
Originally Posted by rodrieguz
I'm going to hunt for this pulley today,

what am I doing wong when the needle won't pick up the bobbin thread?

I've rethread both with no luck. I lifted the machine up to look underneath turning the wheel towards me to pick up the bobin thread, the out side of the bobbin case moves but the inside were the bobin is does not move???
Is the needle in correctly? Have you ever had a mechanic look at the machine?
04-26-2011 08:54 AM
rodrieguz I'm going to hunt for this pulley today,

what am I doing wong when the needle won't pick up the bobbin thread?

I've rethread both with no luck. I lifted the machine up to look underneath turning the wheel towards me to pick up the bobin thread, the out side of the bobbin case moves but the inside were the bobin is does not move???
04-26-2011 04:47 AM
DanTwoLakes
Quote:
Originally Posted by bentwings
1 3/4" x 3/4 " die cast pulley from Tractor supply is a bolt on.
To the sewing machine's motor. You'll probably have to bet a different belt, too.
04-25-2011 08:55 PM
bentwings 1 3/4" x 3/4 " die cast pulley from Tractor supply is a bolt on.
04-25-2011 04:50 PM
rodrieguz
consew 206 rb-5

Thanks Dan,

right on the money, now if I can just slow this beast down.
04-25-2011 03:41 PM
DanTwoLakes Stitching should be equally tight from the top and from the bottom. If the thread is straight on the bottom, the tension is too tight on the bobbin case, or the top thread tension is too loose. If the thread is straight on the top, the top tension is too tight, or the bobbin tension is too loose.

Look at page 13 of this Singer manual, it is explained very well: CLICK HERE
04-25-2011 03:28 PM
rodrieguz
consew 206 rb-5

I purchased this machine a couple days ago and can't seem to get it to stitchs correctly. (Or in my mind) the loop that's usually found on the bottom of the material that holds the stitches tight is on top???? Is this correct??? the manual I have is very vague in analizing these thread issues.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.