Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Blowby Crispies
User Name
Password
lost password?   |   register now

Thread: Blowby Crispies Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-27-2011 06:21 PM
mud bros you wont need to use rottela as it tends to loosen all the junk accumulated over the years due to high detergent levels.
it is good oil tho

mobil 1 syn would be easyer on loosening crud
and still have great protection(something i dont think will help now)


i think the egr is external on the tpi so that kills that idea too.

i guess its just plain wore out
04-27-2011 05:44 PM
123pugsy Thanks.

Oil is Shell Rotela.

The stock cam is actually 114.5 LSA.

Its a TPI setup.

The EGR crossover cooking the oil is a good thought although the blowby seems quite severe.
04-27-2011 05:36 PM
mud bros that cam should work well its not overly large

problem is the egr crossover in the manifold bakes the oil and turns it to crusty crap the tbi system also runs on the lean side raising the operating temp of the engine.

also sounds like your using cheep oil as better oil can handle higher temps before turning to coke.
04-27-2011 05:18 PM
123pugsy
Blowby Crispies

I took off the passenger rocker cover from my 350 small block and found black sand like particles along the edge of the gasket and also starting to form inside the cylinder head. I knew I had some blowby as it was coming out the breather which I had installed on top of about a 10'' high tube to try to keep oil off the engine.

PCV valve may not be as effective as it should as this is a TPI engine with the wrong cam and vacuum drops off immediately upon acceleration.

I take it this blowby comes from the rings and is making its way to the cover with the breather as its the easiest place to flow to.

The block was rebuilt about 30 K miles ago and taken out of my last truck and left in the garage for a couple of years.
I then took it to a guy that does alot of high performance stuff and he recommended honing and new rings, bearings, cam, lifters. This was from a visual inspection.

I had asked originally to bore it out .060 but he persuaded me not to.

Is it rebuild time or time to change the cam and hopefully get better vacuum for the PCV system?

Can Specs: Comp CS 260H-10
Operating Range: 1200-5200 RPM
Duration Advertised: 260 Intake / 260 Exhaust
Duration @ .050'' Lift: 212 Intake / 212 Exhaust
Valve Lift w/1.5 Rockers: .440'' Intake / .440'' Exhaust
Lobe Separation Angle: 110

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.