Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> Removing Aftermarket Billet Interior Door Handle
User Name
Password
lost password?   |   register now

Thread: Removing Aftermarket Billet Interior Door Handle Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-01-2011 12:24 PM
brickyardboy
Quote:
Originally Posted by cajun1955gmc
Sorry I forget to mention take the handle off first. That bolt holds it on. Once handle is off then the bezel will come off. There is a cylinder under it. That's were your two red lines point two. The cylinder has the set screws. Mine has two set screws.
I hope that helps.
You're right. The bezel was on really tight, but managed to pry it off, which exposed the two set screws which released the part that slips over the splined shaft. This one threw me because I've used the GM door tool before to slip behind the bezel on other cars and push out the spring clip to release the handle, but this one wouldn't allow any room to push the door panel away from the handle bezel to slip the tool in. Now I can get inside the door to see why the outer handle doesn't open the door. I'm thinking that the return spring is either broken or has fallen off, I'll soon see. Thanks again, guys!
05-01-2011 05:42 AM
brickyardboy Thank you both for your helpful information. I will hit it again later today.
05-01-2011 04:09 AM
DanTwoLakes
Quote:
Originally Posted by brickyardboy
There's no visable set screws on the billet aluminum bezel. This handle is on a '34 Ford coupe glass rod, but it's a generic billet handle that most street rods would use. I just thought that someone may recognize this particular handle, and can give me a clue as to how it's removed. Thank you guys for your input.
Yes, I realize it's a generic aftermarket handle. The handle is not the issue, the issue is what the handle is mounted on. Most handles on older cars are pushed on a splined shaft and have either a pin holding them on (Ford used pins) or a wire spring clip holding them on (GM used clips). This was complicated by a spring behind the door panel that pushed the door panel tight against the back of the door handle. Your problem is what was used for your door handles to be mounted on.

If either of those retainers was used you have to push the door panel back away from the back of the handle to get at it.
If you feel a groove an both sides of the handle, it has a spring clip holding it.

In any case, the handle would be on a splined shaft. If you take out the allen head bolt in the center, the handle should pry off. It may just need more persuasion than what you are using.
05-01-2011 01:15 AM
cajun1955gmc Sorry I forget to mention take the handle off first. That bolt holds it on. Once handle is off then the bezel will come off. There is a cylinder under it. That's were your two red lines point two. The cylinder has the set screws. Mine has two set screws.
I hope that helps.
04-30-2011 10:07 PM
brickyardboy There's no visable set screws on the billet aluminum bezel. This handle is on a '34 Ford coupe glass rod, but it's a generic billet handle that most street rods would use. I just thought that someone may recognize this particular handle, and can give me a clue as to how it's removed. Thank you guys for your input.
04-30-2011 08:23 PM
DanTwoLakes What make, model, and year car is the handle installed on?
04-30-2011 03:55 PM
cajun1955gmc There should be set screws on the piece that the handle is screw to. The set screws hold it to the spline shaft.
04-30-2011 02:00 PM
brickyardboy
Removing Aftermarket Billet Interior Door Handle

I'm having a problem removing my interior passenger door handle. Because I can't pull out the door panel enough to see how this handle is attached to the inside hardware, I can't determine what's holding it on, and thought someone may be familiar with this particular door handle. After removing the cap, I've removed the allen screw in the center, and even the two roll pins (photo) but it still won't budge. Would appreciate anyone's input. Thanks...

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.