Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Has anyone got torque specs for installing the 4l60e+....
User Name
Password
lost password?   |   register now

Thread: Has anyone got torque specs for installing the 4l60e+.... Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-23-2011 09:39 AM
mitcht2005 one thing i always do especially if you are reusing converter bolts, i use blue lock tight..

here are a few specs,

Transmission to Engine Bolt 35 lb ft

Flywheel to Torque Converter Bolt 46 lb ft

Heat Shield to Transmission Bolt 13 lb ft
05-21-2011 01:51 PM
Altec Practice makes perfect. If you are working on something where you have time simply mess around with your wrenches, ratchets, and air tools while following with the torque wrench. It really helps give an idea of what amount of force does what.

After a while you can tell what your impact is doing by sound, and feel. Same goes for wrenches, and ratchets. You can feel it tightening. You can even feel the bolt stretching! The worst part is adjusting your force based on the leverage of the tool. Well, that and if you are messing with stuff like aluminum, or stainless. Yuck.

Unless we hit a time warp, it isn't possible for me to have anywhere near 30 years experience.

Oh, after you figure it out you can start betting people you can tighten something within a certain range! Easy money!
05-20-2011 11:17 PM
old yukon I wish i had the the sense of knowing when it is just tight enough, I don't have the 20 - 30 years experience in bolting up stuff on a car.

You guys are are like the head chef who never follows a recipe, I'm like the apprentice chef, who measures and weighs everything.

I think i have a about ten year to go before I throw away my torque wrenches, verni calipers, and feeler gauges.

I just check hunting till I find the torque specs, or use blue and red locktite on everything LOL !!!
05-20-2011 04:00 PM
Altec
Quote:
Originally Posted by tnsmith10
i havent used a torque wrench on these items ever as i do trans R&R for a living and just use my impact guns. 3/8" drive for everything except for the trans to the engine. and for that i use my 1/2" gun with a 3 ft extension. i zip it flush and give it a couple short bursts.
as far as the rear drive shaft, if its steel i use the 3/8" gun, if its aluminum, i tighten it by hand.
the heat shield that goes on the passenger side of the case, i just tighten by hand as well. maybe 15-20 ft lbs.
after 20+ years, i dont have anything come loose on me or do i have a problem with removal in case the trans has had to come back out
Pretty much what I do as well.

If you are concerned though you can look up the bolt size, TPI/Pitch, and the grade of the bolt to get the general torque specs. Plenty of charts on the internet.
05-20-2011 03:12 PM
tnsmith10
Quote:
Originally Posted by old yukon
Has anyone got torque specs for installing the 2000 4l60e to the 5.3L SLT engine, with np246 t/case. So many variations in specs out there .


transmission to the engine.
Flywheel to torque converter
Exhaust Manifold Bolts
heat shield to transmission.
transmission rear mount.
transmission cross member
Driveshaft- rear axle
Starter to engine

Thanks guys
i havent used a torque wrench on these items ever as i do trans R&R for a living and just use my impact guns. 3/8" drive for everything except for the trans to the engine. and for that i use my 1/2" gun with a 3 ft extension. i zip it flush and give it a couple short bursts.
as far as the rear drive shaft, if its steel i use the 3/8" gun, if its aluminum, i tighten it by hand.
the heat shield that goes on the passenger side of the case, i just tighten by hand as well. maybe 15-20 ft lbs.
after 20+ years, i dont have anything come loose on me or do i have a problem with removal in case the trans has had to come back out
05-20-2011 09:53 AM
old yukon
Has anyone got torque specs for installing the 4l60e+....

Has anyone got torque specs for installing the 2000 4l60e to the 5.3L SLT engine, with np246 t/case. So many variations in specs out there .


transmission to the engine.
Flywheel to torque converter
Exhaust Manifold Bolts
heat shield to transmission.
transmission rear mount.
transmission cross member
Driveshaft- rear axle
Starter to engine

Thanks guys

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.