Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Acrylic Enamel Help
User Name
lost password?   |   register now

Thread: Acrylic Enamel Help Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-29-2011 12:58 PM
Hotbo i have sprayed several AE metallics back many years ago and they are the most aggravating SOBs to get to lay right and then you can sand and buff the trash.

PITA imo!
05-29-2011 11:38 AM
mitmaks I painted a boat for a guy with AE. It was metallic color and was a pita to lay out and I'm experienced painter. Customer was tight so he didn't want to spring for base/clear
05-29-2011 11:18 AM
deadbodyman acrylic enamals are OK if you dont mind repainting every two yrs ...even Nason urathane holds up for ten yrs.....even WITH the hardner AE will fade out in three yrs max...I'd spend an extra 50.00 and get any urathane before using an acrilic enamel again. unless its a trailer or one uses it any more on cars,dump trucks and bulldozers yes ...and absolutely no one uses it with metalics only solid colors even on heavy equipment or Semi's...
Years ago I had to paint 50 dump trucks in red Centari acrilic enamel ,They were turning pink before I finished all of them (Fla sun) so we went with a low end urathane, problem solved ,big differance in quality...for just a little more cash..
I wouldnt advise anyone to use a SS metalic (urathane or acrylic enamel) its tough to get looking right without experiance ....and it never looks REALLY good ,just good enough...
05-29-2011 08:54 AM
Hotbo the problem with Metallic AE is you cant sand and buff it.

it shifts the metallic around.

2nd problem is depending on the color it can be a real Mutha Fer to spray and get to lay out correctly.

if you decide to stay with AE do not waste your money on the cheaper lines.they are Pure Junk

Best of luck Travis
05-29-2011 08:34 AM
matt167 I'v used both PPG Delstar Acrylic enamel and Restoration Shop Acrylic enamel.. Restoration shop seems to flow a little better.. FWIW, I use a Campbell Hausfeld gravity feed gun that I got at Walmart. Nothing expensive
05-29-2011 07:39 AM
shine there is nothing wrong with ae with hardener. i'd use it before omni or nason junk .
05-25-2011 06:50 PM
minibiker2258 I understand that it is not top of the line but I'm not looking for that either. And something reasonably cheap and easier to spray is what I'm looking for right know.

05-25-2011 07:01 AM
oldBodyman +1

acrylic enamel was never a 'top of the line' paint system, it was cheap, fast and easy but never lasted too long, even with the hardener. That was 30 years ago and it has only dropped down the food chain since.
05-23-2011 07:44 PM
Old Fool If you want a non clear coat finish, use single stage urethane.
Don't buy the cheap crap like Omni or similiar, get a pint or qt of top line paint like Concept.

On a small job the difference in material cost is minimal, but the end product and durability will be more than worth it.
05-23-2011 06:54 PM
Acrylic Enamel Help

I recently joined this forum after reading many many threads regarding painting and other topics and have a question. Do most people recommend NOT using Acrylic Enamel Metallic paints. I plan to use a good primer, hopefully an epoxy primer, then top coat with acrylic enamel metallic, with no clear coat.
I have been advised against this and just want to hear some other opinions.

Also if anybody would like to recommend another paint type for me to use, but since the price is more reasonable and this is a small project not a special show car or anything I would really like to keep it simple.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 04:55 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.