Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 3 oil pressure switches?
User Name
Password
lost password?   |   register now

Thread: 3 oil pressure switches? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-26-2011 06:46 AM
1ownerT
Quote:
Originally Posted by joe_padavano
You don't need three switches. You can combine the oil idiot light and the fuel pump safety switch by using a Standard Motor Products PS64 sender. This sender has three terminals. The center terminal goes to the idiot light and the outer two terminals are connected together when there is oil pressure to run the fuel pump.

Great tip!
05-26-2011 05:59 AM
staleg Just an update.
I found out about it. The standard "idiot lights" have an oil pressure switch that turn on the light when pressure goes below 20 psi.
The fuel pump safety swith that I already have bought, shuts down the pump when the pressure goes below 7 psi.

I will probably buy an "idiot light" kit. Those kits often have the needed tee coupler enclosed, too.
05-25-2011 02:51 PM
staleg Thanks for the answers. Lots of good info as usual!

But maybe I don't need the oli pressure warning light, since I have the oil pressure safety switch for the fuel pump? What do you think?

To make any sence, the warning light must get on by a little higher pressure than the fuel pump safety switch will shut off the pump, right?

The safety switch I have bought will shut down the pump by an oil pressure below 7 psi.
The warning light kit i might buy have a 20 psi sending unit. Forgive me for this stupid question, but is this for warning the driver about too high oil pressure, or too low...?

The engine is a close to standard 350 small block chevy, by the way.
05-23-2011 09:19 AM
joe_padavano You don't need three switches. You can combine the oil idiot light and the fuel pump safety switch by using a Standard Motor Products PS64 sender. This sender has three terminals. The center terminal goes to the idiot light and the outer two terminals are connected together when there is oil pressure to run the fuel pump.

05-23-2011 06:46 AM
sqzbox Should be another plug on the front of the block just behind the water pump.
I put my oil pressure gauge line there because I like to see the pressure reading from the furthest point from the pump.
05-23-2011 06:43 AM
curtis73 You can put a tee at any one of the ports to get two holes, or just wire a relay to one switch. Just ground the fuel pump relay to the oil pressure switch so the fuel pump comes on with oil pressure and use the other post on the relay for the oil pressure light.
05-23-2011 03:30 AM
Jake_Dragon port below the distributor is a good place.
thats where mines at
05-23-2011 03:00 AM
staleg
3 oil pressure switches?

I need 3 oil pressure switches on my Chevy small block engine.
1 for an oil pressure warning light
1 for the oil pressure gauge
1 for electric fuel pump safety cut-off.

Where Do I mount them? Speedway Motors are selling a 1/8" NPT tee fitting that fits in the oil pressure switch location above the oil filter, but what about the third one?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.