Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> DIY ideas for a long flexible sanding board?
User Name
Password
lost password?   |   register now

Thread: DIY ideas for a long flexible sanding board? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-07-2011 05:15 PM
hp246 For long flat pieces, I use scrap cedar. I attach wood handles with countersunk screws. If I need a board contoured to groves cut into the sheet metal (ie: 73-79 Ford F-100 "dentside") I mix up a batch of body filler, use a piece of wax paper and contour the whole mess to the contour of the groove.
06-07-2011 02:15 PM
JohnnyK81 Cboy, you're right, I shouldn't have discounted plexi.

Found some 3/8 - 1/2" stuff precut to 2.75.. Has the perfect amount of give!
06-07-2011 09:56 AM
JohnnyK81 Thanks tons guys! I don't think I can afford to by buying any more sanding blocks.. Just have a quarter and roof to go on this car, then, hopefully, I never tough body filler again. haha..

cboy, I guess it's plexi glass for me! Thanks for the pictures.. My PSA sandpaper is a precious commodity. I wonder if I could glue on some paper clips (As in, the clips on the end of normal sanding boards). Might be so long that the paper would just slide off in the middle though.
06-07-2011 07:00 AM
Arrowhead I was using the aluminum yard stick like cboy posted, but it was very difficult to hold and control. I suppose I could have countersunk some scews and put handles on it, but I never got that far.

I know your looking for a home made solution, but I bought a couple of AFS sanding boards and they are the best investment I've made so far for bodywork tools. They are not cheap, but the time and energy saved was well worth it to me. They have removable metal rods in them, the fewer the rods, the more flexable they get. The face is thin steel so it will flex along large curves and sand off the high spots. I have a 16" and a 27"

http://www.adjustflexsand.com/products.html
06-07-2011 06:57 AM
cboy
Quote:
Originally Posted by JohnnyK81
...but I still think I'll need something longer for the roof, and possibly quarters of my fastback.
Not only longer sanding blocks...but I found longer "spreader tools" are helpful as well. And plexiglass isn't a bad way to go.

Here is a plexiglass "bondo applicator" that I used on my sedan/delivery:



And this applicator is simply a piece of roof flashing (you have to cut a very straight edge on it or use the pre-cut edge at all times). Gets the filler spread thin and even over some pretty difficult curved areas.





And here is my long plexiglass block sander. The "handles" are 35mm film canisters epoxied to the back side of the block. And the sandpaper is stick-on type.



And here it is in use.



Although I didn't try it, I've also heard of folks using aluminum 4' "yard sticks" such as the one shown here. These would bend nicely to conform to any slight crown in the metal while remaining flat over a very large surface area.
Holding on to them might be the biggest challenge.

06-07-2011 03:06 AM
willowbilly3 On a smaller scale, I use tightly rolled newspaper with several layers of duct tape wrapped around it, makes a great contour sanding "board". You might try something like UHMW plastic and bond some thin high density foam to it.
06-07-2011 12:33 AM
JohnnyK81
DIY ideas for a long flexible sanding board?

I bought some Durablocks, but I still think I'll need something longer for the roof, and possibly quarters of my fastback. What has everyone else come up with? Only thing I can think of is plexi glass, but not sure if I like that idea.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.