Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 350 Trans slipping please help :(
User Name
Password
lost password?   |   register now

Thread: 350 Trans slipping please help :( Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-12-2003 09:57 PM
airworld2
350

put a fork in it , its done. forward is gone rebuild time..... enough said!!!!!
09-12-2003 08:16 PM
Crosley
I enjoy the comments

Quote:
Originally posted by adtkart
Typical comment from someone that knows nothing about transmissions. As has been posted on this board numerous times. It WILL NOT do any good to change the trans filter on a trans that is not working. The only thing that changing the filter will help, is the financial condition of the business that sells the fluid and filter.

If there is anything in the pan that will plug the filter, the trans is junk. I don't for the life of me, understand where you people think this stuff that "cloggs" the filter comes from. If changing the fluid would make the trans work, it will also cause additional damage to hard parts that are not included in a rebuild kit by allowing you to use it while it is destroying itself..
09-12-2003 07:57 PM
adtkart
Re: DIY?

Quote:
Originally posted by senor_limpio
Is it possible for you to replace the clutch packs yourself? It does sound like they're toast. If you haven't pulled it yet, you might wanna even try just replacing the filter. May be all clogged. But like was already said... symptoms sound like toast.
Typical comment from someone that knows nothing about transmissions. As has been posted on this board numerous times. It WILL NOT do any good to change the trans filter on a trans that is not working. The only thing that changing the filter will help, is the financial condition of the business that sells the fluid and filter.

If there is anything in the pan that will plug the filter, the trans is junk. I don't for the life of me, understand where you people think this stuff that "cloggs" the filter comes from. If changing the fluid would make the trans work, it will also cause additional damage to hard parts that are not included in a rebuild kit by allowing you to use it while it is destroying itself..
09-11-2003 10:36 PM
senor_limpio
DIY?

Nice attack... You're too cool! I'll admit that I may not know everything there is to know about transmissions, but I have rebuilt a few in my day and none crapped out on me. Just because I don't own a transmission shop doesn't mean I don't know anything about transmissions. If my comments are not appreciated.. I will not post here...

Rock on...
09-11-2003 10:08 PM
slingslingbinks i built a 4l60 that went less than 25 miles, i rolled the small lip seal on fwd. clutch piston, even after air checking it 10 time' s. it was in a 4x4 chevy sub. it took out every clutch pack. verry costly come back good luck c-ya sling
08-27-2003 04:09 PM
Neil_UK wont be driving there! (unless in reverse all the way!!!!)

It'll be a case of drop it out and give it to em

Well 200 Miles to wreck a rebuilt trans must be some sort of record???
08-27-2003 04:05 PM
BstMech Over there in England I bet the shops look at an American car kinda' how we do an English car. Going by that, I would say it's not going to be cheap by far. I do know that over here if you pulled the tranny and looked around, you should be able to find someone to patch it for less than a couple hundred bucks total parts and all. If you did it all your self, you could do it for less than fourty bucks total. I'll say about twice that in your neck of the woods. To just drive the car to the shop and say "fix it", would cost about 800-1200 dollars or more here.
08-27-2003 03:42 PM
Neil_UK we put in 4 quarts in all. is this a big (expensive) job?
08-27-2003 03:29 PM
BstMech What probably was the thing that killed it was when you limped to your friends. How many quarts low was the tranny when you first noticed it was low? The symptoms you describe (good reverse but no forward gears and the fluid smells with small dusty particles), suggests the forward clutches are gone.
08-27-2003 03:16 PM
Neil_UK not good news, but why? is it the low fuid that did it? should I have not limped the car to friends but got them to come to me?
08-27-2003 03:03 PM
BstMech I'll put my money on your forward clutches being toast.
08-27-2003 02:41 PM
Neil_UK
350 Trans slipping please help :(

Hi,

I had my tranny rebuilt and fitted it myself. on the first real journey out (about 50 miles round trip) we had apipe come off from the trans to the oil cooler resulting in loss of fluid. I got the pipe back on and limped the car to friends (about 2 to 3 miles) and replenished the fluid (with a circlip this time <blush>) and drove home a little low on fluid(?) I thought. since then we went to a show and things were fine. until the other day when visiting other friends, fine up until we cam to go, and then the car slips in drive with a judder if it is revved. Reverse id fine but 1st 2nd and 3rd all slip. I checked the fuid which now seemed high. so drained a quart out which took it about 1/2" below the hashing on the stick, but it still slips

the fluid I removed smells slightly and there were some small dusty particles in the bottom of the tray.

Have I ruined my trans? I am supposed to be the wedding car at a friends wedding in 2 weeks.

please help!

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.