Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Bear claw latch with stock outside door handles
User Name
Password
lost password?   |   register now

Thread: Bear claw latch with stock outside door handles Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-15-2011 09:09 AM
yragat Thanks
The body is already reinforced all the way down the door jamb,so I'm OK there

Never changed my Avatar---don't have the Model T anymore this is the new one
07-14-2011 01:20 PM
Irelands child Those bear claw latches don't have to go in the exact same position as the OEM's. You can mount them lower and run a bell crank and rods to the handles. While I don't have the outside handles, ran mine with that bell crank and a pair of rods and a return spring. As far as the exterior paint - well, you'll have to be careful, but you will have to repaint the door jambs:



Shows the rods and an electric actuator that is now been replaced by a spring 'hanger'



Upside down



Shows the door release

I also have a suicide door safety pin as the mini bear claw latches while much better then the original latch still have only a single rotor.

Not a job for the faint of heart, as I ended up using a circle saw and adding a couple of access holes to the inner door panel - see the brighter red rattle can primer. You also might consider adding some reinforcing to the body at the door striker - that metal is puny at best

Dave W
07-14-2011 11:51 AM
471A The raised portion was fabricated to make room for the latching mechanism.
07-14-2011 11:09 AM
yragat
Quote:
Originally Posted by 471A
Attached photos
Thank you,did your door always have the raised portion,or did you have to do that to accommodate the new latches?
07-14-2011 10:30 AM
471A
See attached photos

Attached photos
07-14-2011 10:25 AM
471A All of the attached photos depict the 29 Tudor passenger side door. Driver's side installation is the same. Ignore the duct tape.......
07-14-2011 05:47 AM
yragat
Quote:
Originally Posted by 471A
I have a 29 Tudor with stock exterior door handles and mini bear claws. I will recruit my tech-savvy daughter to take digital photos and, assuming that is possible with this website, post the photos of how this was done. Inside the car, the "door handle" is a simple straight rod that slides up and down to open and close.
That would be great
Thanks
07-14-2011 12:20 AM
471A I have a 29 Tudor with stock exterior door handles and mini bear claws. I will recruit my tech-savvy daughter to take digital photos and, assuming that is possible with this website, post the photos of how this was done. Inside the car, the "door handle" is a simple straight rod that slides up and down to open and close.
07-13-2011 08:44 PM
yragat
Bear claw latch with stock outside door handles

I have a 30 model A Roadster and am thinking about installing the mini bear claw latches in it this winter. This car has stock interior and exterior door handles. Is there a way to keep (especially) the outside handles and make them functional with bear claw latches? I know that a car without windows that I could reach inside to open,but then what do I do about the outside handles---can't shave,the car is already painted

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:25 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.