Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Rear End Ratio - measured and number looks way too low - what am I doing wrong?
User Name
Password
lost password?   |   register now

Thread: Rear End Ratio - measured and number looks way too low - what am I doing wrong? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-27-2011 07:37 PM
ggevaert
Also likes Chevy trucks and boobies - go figure

Thanks Fast68, guess what, I also like Chevy's and Boobies, weird eh!

I actually had both wheels off the ground when I did it and turned the passenger one and measured the driveshaft. Then I went and also did the measuring by turning the driveshaft and it spun the passenger tire only (no Posi).

Thanks Everyone

Gary
07-25-2011 10:06 PM
fast68 2.6 is what you found.

thats basically gonna point at 2.73...

sometimes when youre counting rotations you end up needing to double what you find, depending on how you did it

one wheel on ground or both off ground.

will change what number rotations you get.

doing it with one wheel on the ground will be most acurate and easiest...


note: 2.21 and 2.56 were available and uncommon ratios in these trucks as well over the years, after 1972 when the awesome CST generation of trucks ended.....

not as common ratios as others such as the 2.73 and 3.07 and such....

GM had alot fo oddball ratios in the trucks....

2.56 and 3.40 were a couple of the least common ones....

2.21 was another uncommon truck ratio too actually.. i forgot about that one almost... ive only seen one or two actual 2.21 trucks ever in my life, listed on the RPO sticker and all...
07-24-2011 07:11 PM
NEW INTERIORS You have to turn both tires together..
07-24-2011 07:08 PM
ggevaert
Excellent

Thanks, that makes sense then and matches what the spec sheet says. I did not know that about the doubling but makes perfect sense.
I wanted to double check as the person I got the truck off of did not indicate whether it was changed and if it was already between a 3.40 and 3.80 then I wasn't going to bother as that matches the engine/tranny setup. However, I forgot about the posi part so even if the gears were correct I would have needed to change it anyway.

Cheers
07-24-2011 11:52 AM
sqzbox Yoy could probably do better just posting your tranny and RPM at 60 mph on here to find what ratio it is.
07-24-2011 10:50 AM
joe_padavano
Quote:
Originally Posted by ggevaert
The instructions don't say anything about doubling the number you come up with (which would then make more sense)
Doubling is EXACTLY what you need to do for a non-posi axle. Since you're only spinning one wheel, you're losing 2:1 in the spider gears. Now your 2 2/3 looks a lot like 2.73:1. By the way, I usually turn the drive shaft ten times. It's a lot easier to see the difference between 32.3 and 34.2 turns of the wheel than 3.23 and 3.42, for example.
07-24-2011 10:28 AM
ggevaert
Rear End Ratio - measured and number looks way too low - what am I doing wrong?

Hello Everyone,

Finally got a chance to try to determine my rear-end ratio (1984 GMC pickup truck with stock rear end sofar) so followed the steps whereby I jacked up the truck and marked the driveshaft and tire then spun the tire one circle to determine the number of revolutions the driveshaft makes.

And; I get 1 and 1/3 turns out of the driveshaft for one wheel rotation. Just to be sure I spun the driveshaft by hand one rotation and the tire went 3/4 of a turn.

I was expecting something like 2.73's (as per data sheets for that year) but 1.3??

Am I doing something wrong or is that possible. The instructions don't say anything about doubling the number you come up with (which would then make more sense)

Thank You
Gary

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.