Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Restoration Job question - paint/clearcoat
User Name
lost password?   |   register now

Thread: Restoration Job question - paint/clearcoat Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-27-2011 11:26 AM
MARTINSR My experience in these things brings me to the sand blasting suggestion for more than just one reason. One of these reasons is that often these things have been painted a number of times, often with very poor paint. So this is what you may have under all that. The other thing that I have seen is that because it has been painted a few times (possibly) detail has been lost under all that paint. When you sand blast it and paint it, it often will "pop" much more, often blown away "pop" that was buried before.

07-27-2011 11:12 AM
spaulgal I'm no pro, but I've used 2-part Glamour Clearcoat with very good results.
I'll give it a try over the rustoleum/lacquer after a scuff and see how it looks.

There are a few other small parts that need painting. The axel, wheels, etc.
The best way to match is to use the same paint. Can I use Rustoleum as the base and the Glamour CC over (skipping the lacqeur)?
Or should I try to color match with enamel?
07-27-2011 10:54 AM
witty73 Have you used clear coats in the past? If you have, I would use what you are comfortable with. Any clear is going to have the same basic effect when you are finished. The difference alot of times is what kind of environment you are working in, what kind of equipment you have, etc. HVLP gun or Firehose? If it was me, I would use a high quality, catalyzed automotive clear coat.

At the auto parts store, ask for a clear coat that has a slow, or standard reducer. I wouldnt suggest anything with a fast reducer or hardener as it speeds up dry time. It may take you a little longer, but I think if you use a cc with a slower dry time you wont find yourself rushing to finish. Myself, once I start to rush because its drying to quick on me, I start to fight sags and runs.
07-27-2011 10:51 AM
spaulgal Should I try to shoot with a 2-part CC with hardener?
Will I likely get more lasting results?

Yes, this will be mostly indoors (besides occasional events - where is might be outside as a centerpiece)
It will be in an exposed area with lots of windows

07-27-2011 10:14 AM
witty73 My thought is that the Plasticote laquer was a semi gloss or even perhaps a satin. His intentions were good, but probably not the right product. Or, if it was a full gloss product, it may not have the UV protection of true clear coat and has dulled. You could try waxing it, but for longevity purposes I would probably clear it.

First thing I would do is take a scotch brite to an inconspicuous area and scuff it a little so it is real dull. Then I would shoot a couple of wet coats of CC on it and let it dry. This should give you a good indication of what it will look like going that route. If you are satisfied with the results, once the "test area" has sufficiently cured, I would scuff the whole thing and clear it.

If you are not satisfied with the end result, I would scuff the whole thing, making sure to sand out any imperfections with paper. If it is rusted, you may need to sandblast, but chances are if it is not you can just scuff the whole thing nice and dull. Cover any exposed metal areas with gray or preferably black primer, shoot two coats of black base coat and then clear it. Good luck
07-27-2011 10:00 AM
BarryK I agree with Brian 100%.

However, will add this.
Since I ASSuME this will always be indoors?? You could gray scuff pad the lacquer clear and coat with a urethane clear and would most likely last for years, if this would be outdoors, then it will not last and should not be done.
07-27-2011 09:45 AM
spaulgal You don't think there's anyway to salvage the portion that is already done?

It actually looks decent - but very little gloss. CC over won't work?
07-27-2011 09:40 AM
MARTINSR When I hear the description of your project the first thing I think of is sand blast, epoxy primer then a urethane SS or a urethane bc/cc. Sounds very cool by the way.

07-27-2011 09:24 AM
Restoration Job question - paint/clearcoat

Hello all--

We recently purchased a great piece of an old Hollywood studio. It is a large camera crane from the 1940. Unfortunately, it was kept outside for years and looked beat

I just restored the "Boom Arm" section which was all brass, iron and, aluminum. That part now looks incredible. Now, I need to "cart" section. It kinda looks like the chariots used on Ben-Hur!

Most of it is heavy gauge steel -- very craft-fully put together. The previous owner tried to restore this part of it and used Rustoleum Glossy Enamel on it and cleared it with PlastiKote Lacquer. It looks ok, but flat - it doesn't pop.

So what should I do? I was going to try to used the 2-part Glamour ClearCoat overtop of the Lacquer. The other option is to remove all the paint and lacquer and start over.

This will be a showpiece for us - we are a movie production company and will use this in our lobby.



Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:45 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.